YAPSC:10V : The glue between Step/dir and +/-10V servo amp - Page 12

Page 12 of 13 FirstFirst ... 2910111213 LastLast
Results 221 to 240 of 260

Thread: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

  1. #221
    Registered
    Join Date
    Nov 2012
    Location
    Portugal
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    boa noite
    Tambem estou interessado nas pci
    Voçe consegui alguma?



  2. #222
    Member
    Join Date
    Oct 2009
    Location
    asD
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Got some boards from Andy and need help.

    My setup is PC <> YAPSC:10V <> PAC SCI SC-903 <> PAC SCI R33 motor.

    - YAPSC fw: 2.0.7, tuning tool YT 1.3.4.

    - About SP-903 configuration don't know nothing (no interface card), tried step/dir control, no response, then tried analog cmd and motor started to spin, after that found YAPSC.

    - Wired everything, first test and got some problems, motor oscillates cw - ccw see videos (sorry for poor quality, old phone)





    - after several seconds YAPSC goes to maxerror, and drive goes to fault Nr.4 (err4.jpg).

    - P set to -0,22 (tried from -0,001 to -1 same result [- because with + i get maxerror fault at startup]), I and D 0.

    - encoder gives good feedback, tried to rotate shaft with disconected motor power and YTT reads about 8200 steps/rev.

    - also find out that driver SC-903 response just when YAPSC output is higher than +5V.

    Would be great to hear any suggestions, since i'm new to servo systems, but not new to automation ant process control.

    Saulius

    Last edited by sla; 10-15-2014 at 11:10 AM.


  3. #223
    Registered
    Join Date
    Jan 2005
    Location
    Latvia
    Posts
    30
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Hi Lucas

    Are you still selling your boards?
    I have CNC VMC with Simodrive 611 and Sinumerik 820M. Would like to change Sinumerik to another Chinese cnc controller (GSK or Adtech) but would like to keep Simodrive drives with motors.(x,y,z, toolchanger, spindle - all of them use simodrive).
    What do you think, are these boards stable to use on production machine?


    Best regards,
    Oskars



  4. #224
    Registered
    Join Date
    Feb 2014
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Hi lucas

    I am using pulse to analog - one of my friend prepared for me. It works fine but only problem is reverse direction. I need convertor which change direction of signals as per mach direction output

    Please guide me for this


    Sent from my iPhone



  5. #225
    Registered
    Join Date
    Jan 2007
    Location
    Slovenia
    Posts
    93
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    If anyone interested for UHU servo controller with analog (+/-10Volt ) output visit Custom Machine Design

    I have designed UHU servo controler witch can control analog ( velocity,torque ) linear servo amplifiers.

    Also , avaible only boards to assemble. 4 PCB avaible. Price 8.50 eur .

    If interested, PM .



  6. #226
    Registered
    Join Date
    Apr 2008
    Location
    Macedonia
    Posts
    20
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Does anyone have and seal these boards (YAPSC:10V),, If so I need them.

    Please write on my e-mail salex_06@yahoo.com

    Asek



  7. #227
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Quote Originally Posted by Aleksasek View Post
    Does anyone have and seal these boards (YAPSC:10V),, If so I need them.

    Please write on my e-mail salex_06@yahoo.com

    Asek
    I have ( 1 ) that has never been used, has programing key as well

    Mactec54


  8. #228
    Registered
    Join Date
    Jan 2007
    Location
    Slovenia
    Posts
    93
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    I have 3 PCB's for sale . Price is 8 eur /pcb.
    Payment : Paypal

    If interested, contact me.



  9. #229
    Registered
    Join Date
    Nov 2011
    Location
    Ukrain
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Hello!
    I have board YAPSC 10V.
    How can I use the index of the encoder for Homing? (Linuxcnc)
    Is it possible ?
    What are the options?



  10. #230
    Registered
    Join Date
    Oct 2006
    Location
    Bosnia
    Posts
    32
    Downloads
    1
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    visky: "I have 3 PCB's for sale . Price is 8 eur /pcb.
    Payment : Paypal"
    3 x 8 = 24 eura = 1L dobrog viskija



  11. #231
    Member
    Join Date
    Aug 2015
    Posts
    142
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Hi , is there somme nc files for mach 3 , because i strugle with gerber files for some times , and i ca't get them to end , or a cam program to handle that gerber project.



  12. #232
    Member
    Join Date
    Oct 2009
    Location
    asD
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    I have several boards for sale. If anyone need it, please PM.



  13. #233
    Registered
    Join Date
    Apr 2008
    Location
    Macedonia
    Posts
    20
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Quote Originally Posted by nkp View Post
    Hello!
    I have board YAPSC 10V.
    How can I use the index of the encoder for Homing? (Linuxcnc)
    Is it possible ?
    What are the options?
    Hi nkp
    Do you have homing with INDEX? You make something?
    Just asking, it's very interesting.
    Alex

    Asek


  14. #234
    Registered
    Join Date
    Sep 2015
    Location
    United Kingdom
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Does anybody have any of these boards available to purchase or is this project no longer going? Cheers



  15. #235
    Registered
    Join Date
    Jul 2016
    Location
    United States
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    I have 10 PCB's, and lack the time to build. I need some one to build x3 of them for me to test, and you can have the rest.
    Private message me if interested.



  16. #236
    Registered
    Join Date
    Sep 2016
    Location
    United Kingdom
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Hello Lucas

    Your PM settings won't allow me contact you directly. Just wondering if you ever got any further with your YAPSC - type converter.

    Quote Originally Posted by lucas View Post
    There"s some further testing needed, I will publish schematics etc.. when everything works as it should .

    This design is compatible with Max's PCB (connector pinout) but has some changes and improvements, well I consider these as improvements :-)

    - a real RS422 receiver is used for the encoder: 26LS32, capable of differential and single ended encoders and with proper line termination for high speed.
    - works on a single supply: 8 to 24Vdc, + and - 12V are generated by a DC-DC converter.
    - encoder can be connected with a DB9 or screw terminals.
    - stp/dir/enable inputs have optocouplers and can be connected using a PMinmo style flatcable or screw terminals
    - The progkey is compatible, this or Max's version can be used on both designs

    I have 9 PCB"s left now for some beta-testers.

    One thing might change: the drive error input and Yapsc error output, this is very basic now and might need improvement to support more models of analog drives.

    Please send me a PM if you"re interested.




  17. #237

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Quote Originally Posted by Tripet View Post
    Hello Lucas

    Your PM settings won't allow me contact you directly. Just wondering if you ever got any further with your YAPSC - type converter.
    David

    Lucas has not been involved with the YAPSC for some years due to time constraints.

    He walked away from the project at around the time I was looking at them that's why I looked into getting the boards printed myself.

    Andy

    Sent from my SM-G920F using Tapatalk



  18. #238
    Registered
    Join Date
    Sep 2016
    Location
    United Kingdom
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Quote Originally Posted by audioandy1762 View Post
    David

    Lucas has not been involved with the YAPSC for some years due to time constraints.

    He walked away from the project at around the time I was looking at them that's why I looked into getting the boards printed myself.

    Andy

    Sent from my SM-G920F using Tapatalk
    Thanks Andy.

    Looks like the YAPSC project is dead then - what a shame.

    David



  19. #239
    Registered evguru's Avatar
    Join Date
    Nov 2006
    Location
    United Kingdom
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    I think I've got 3 or 4 YAPSC boards sitting around somewhere, just populated with the uController. If anyone would like them, let me know.



  20. #240
    Registered evguru's Avatar
    Join Date
    Nov 2006
    Location
    United Kingdom
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: YAPSC:10V : The glue between Step/dir and +/-10V servo amp

    Quote Originally Posted by evguru View Post
    I think I've got 3 or 4 YAPSC boards sitting around somewhere, just populated with the uController. If anyone would like them, let me know.
    Boards now sold.



Page 12 of 13 FirstFirst ... 2910111213 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

YAPSC:10V : The glue between Step/dir and +/-10V servo amp

YAPSC:10V : The glue between Step/dir and +/-10V servo amp