| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| OneCNC Discuss OneCNC software here. |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#1
03-29-2003, 12:17 AM
| ||||
| ||||
| Demo problem I loaded the lathe demo and when I start the program, it crashes and closes. I'm using win XP. Any ideas?
__________________ Thank You, Paul G Site Owner-Webmaster- Administrator www.rfqwork.com www.cnczone.com www.welderzone.com    |
|
#2
03-29-2003, 12:34 AM
| ||||
| ||||
| Demo I'll load the lathe demo right now on windows xp and let you know. Stay tuned
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
#3
03-29-2003, 12:46 AM
| ||||
| ||||
 Lathe demo Loaded the demo off the disk to xp and it works fine. Might be a bad file on the server or your down load went bad.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Last edited by wms; 03-29-2003 at 01:22 AM. |
|
#4
03-29-2003, 12:23 PM
| ||||
| ||||
| Paul, Were you able to load the Demo file I sent you. And does it open up ok?
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
#6
03-29-2003, 04:24 PM
| ||||
| ||||
| Video card Steve, I too had a small problem with an Nvidia card. Had to set the color to 16 or 24 bit instead of 32. But I could always open the program. The problem was after doing some work and then rendering. Called Mike at OneCNC and he let me in on the color bit setting thing. After that no problems. Did you find something different to do? Are you using a different card? Please tell us more so we may learn from what you found out. 
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
#7
03-29-2003, 04:43 PM
| |||
| |||
| I have a Geforce 4200 card . I had talked to Mike a couple of times but could only run the older drivers (30.82) . I got the idea of running the " Quadro " Drivers (42.82) . Once I did that I had no problems at all and I'm running 32 bit color. We also use ATI 9000 pro cards at work ($80.00) and they work great . |
|
#8
03-29-2003, 04:53 PM
| ||||
| ||||
| Thanks Steve, Thanks, that's good info. I too am running a Geforce 4200 card. I'll try the " Quadro " drivers. Gald to have here! 
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
#9
03-29-2003, 08:50 PM
| ||||
| ||||
__________________ Thank You, Paul G Site Owner-Webmaster- Administrator www.rfqwork.com www.cnczone.com www.welderzone.com |
|
#10
03-29-2003, 09:21 PM
| ||||
| ||||
| Video cARD CNCAdmin The only reason (ever) a OneCNC demo will not run after proper install is due to a video card driver that has an issue with OpenGL (We are OpenGL certified) in their driver or its the wrong driver/out of date driver. A great way of determing video card driver conflicts is to boot your computer in safe mode (Windows loads only their generic "default" drivers.) The demo should now run, and if so, its time to hunt down new drivers for that card. Tech Support OneCNC LL (877) 626-1262 www.onecnc.com |
| Sponsored Links |
| |
|
#11
03-29-2003, 10:45 PM
| ||||
| ||||
| I will check on that, I have software that uses OPenGL, I will post the error I'm getting.
__________________ Thank You, Paul G Site Owner-Webmaster- Administrator www.rfqwork.com www.cnczone.com www.welderzone.com |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Okuma LC-20 Threading problem | Gunner | Machine Problems, Solutions , Wireless DNC, serial port | 13 | 12-13-2011 11:11 PM |
| OneCNC XR Online Demo | JavaDog | OneCNC | 8 | 08-11-2005 11:25 PM |
| CNC gantry Machine shows problem | Alex S.A | Machine Problems, Solutions , Wireless DNC, serial port | 15 | 04-25-2005 04:02 PM |
| V19 Demo Problems & Questions. | SamLS | BobCad-Cam | 0 | 10-28-2004 12:03 PM |
| Fadal VMC4020A axis problem | cwww | Machine Problems, Solutions , Wireless DNC, serial port | 16 | 12-02-2003 12:07 AM |
| | |
Linear Mode
