Okuma - Page 51


Page 51 of 176 FirstFirst ... 414849505152535461101151 ... LastLast
Threads 1001 to 1020 of 3504

Forum: Okuma

Discuss Okuma machines here.

  1. Newbie- OSP Software Recovery or Rebuild

    Started by kurmay‎, 08-23-2017 06:01 AM
    diskettes, osp, osp500l, software, units
    • Replies: 7
    • Views: 1,302
    08-01-2018, 10:22 AM Go to last post
  2. Unhappy Problem- OSP-P300S - Macturn 550 "Machining" with open door?

    Started by Sammyen‎, 08-01-2018 03:46 AM
    door, looked, make, small, tips
    • Replies: 3
    • Views: 864
    08-01-2018, 08:00 AM Go to last post
  3. Need Help!- Battery Change Utility OSP-7000L

    Started by johnpool‎, 06-18-2018 01:26 PM
    • Replies: 5
    • Views: 1,414
    07-29-2018, 03:01 PM Go to last post
  4. Problem- Macro help please

    Started by Machine_just_went_crazy‎, 07-29-2018 06:03 AM
    basic, call, mastercam, othrd, stuff
    • Replies: 1
    • Views: 719
    07-29-2018, 11:35 AM Go to last post
  5. lathe : arm for catching parts

    Started by deadlykitten‎, 10-31-2016 03:05 AM
    arm, bought, catching, parts, performs
    • Replies: 2
    • Views: 952
    07-25-2018, 02:12 PM Go to last post
  6. Need Help!- Mitsubishi M60

    Started by mayar_wahed‎, 12-15-2017 05:26 AM
    backup, mitsubishi, parameter, plc, send
    • Replies: 1
    • Views: 702
    07-25-2018, 08:16 AM Go to last post
  7. Question Okuma 3D simulation & CAS

    Started by Intersap‎, 07-23-2018 07:59 AM
    3d simulation, cas, okuma
    • Replies: 0
    • Views: 1,510
    07-23-2018, 07:59 AM Go to last post
  8. Programming for Eccentric Turning...

    Started by Jashley73‎, 11-21-2012 07:39 PM
    • Replies: 8
    • Views: 15,693
    07-20-2018, 03:40 PM Go to last post
  9. ATC arm Position on OKUMA MC V-4020

    Started by ANRI‎, 07-19-2018 04:56 PM
    • Replies: 0
    • Views: 299
    07-19-2018, 04:56 PM Go to last post
  10. Okuma Hardisk change

    Started by kurmay‎, 07-06-2018 10:44 AM
    change, disk, hard, ide, ssd
    • Replies: 2
    • Views: 1,168
    07-19-2018, 04:44 PM Go to last post
  11. Okuma MC3VA Z axis ballscrew

    Started by XLVACP‎, 04-01-2018 09:52 PM
    axis, instructions, mc3va, okuma, operation
    • Replies: 1
    • Views: 588
    07-16-2018, 12:42 AM Go to last post
  12. Need Help!- Thread Milling

    Started by machinebob1‎, 07-13-2018 09:23 AM
    books, find, milling, okuma, thread
    • Replies: 0
    • Views: 1,305
    07-13-2018, 09:23 AM Go to last post
  13. Need Help!- Animated Simulation

    Started by gunda‎, 07-10-2018 01:43 AM
    control, machine, milling, p300, properly
    • Replies: 2
    • Views: 1,045
    07-12-2018, 01:57 AM Go to last post
    • Replies: 0
    • Views: 522
    07-11-2018, 10:43 AM Go to last post
  14. Problem- Axis lubrication issues

    Started by 2015imsjfw‎, 07-10-2018 09:51 AM
    alarm, control, lube, switched, waylube
    • Replies: 2
    • Views: 1,282
    07-11-2018, 09:19 AM Go to last post
  15. Okuma Thinc API...

    Started by old timer okuma‎, 10-17-2012 05:54 PM
    • Replies: 1
    • Views: 2,222
    07-10-2018, 02:45 PM Go to last post
  16. install thinc api ?

    Started by deadlykitten‎, 03-23-2016 02:42 AM
    • Replies: 14
    • Views: 4,541
    07-10-2018, 02:35 PM Go to last post
  17. Any swedish MX-45 machine users out there?

    Started by myhäje‎, 11-15-2016 01:12 PM
    • Replies: 9
    • Views: 1,889
    07-09-2018, 08:09 AM Go to last post
  18. Okuma MB56 graphic problem

    Started by brandper‎, 09-11-2012 02:16 AM
    • Replies: 10
    • Views: 2,525
    07-08-2018, 07:38 PM Go to last post
  19. Need Help!- Okuma mx45 toolchanger got stuck

    Started by Maup‎, 12-18-2011 11:58 AM
    • Replies: 3
    • Views: 4,437
    07-08-2018, 05:35 AM Go to last post

Page 51 of 176 FirstFirst ... 414849505152535461101151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 41 users browsing this forum. (0 members & 41 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands