Okuma-Howa manuals

[howd]

Anybody out there have, or know of, anywhere in the world to access manuals for an Okuma-Howa HL20 lathe. It's a 2000 with Fanuc 18T controller. Willing to beg, borrow, rent, or buy.

[rickyt]

What are you needing out of the manuals? Sample codes, alarm list or programming format, I've got a 1999 ACT-20 with an 18T.

[howd]

Hey rickyt, thanks for the reply!!!! Biggest problem at present is 'home zero' that wanders around(both axis, and turret position). This all started with a couple months of machine sitting idle,and the back-up batteries went dead; upon restart I had operator message EX 208 on screen, and alarm lite and beeper, and machine was alarmed out. Further digging showed ACP300 alarms for X,Z, and A(turret) axis. Replaced batteries and got rid of 300 alarms thru reset of 1815 parameters, and after MUCH fooling around, finally got rid of 208. However, turret doesn't seem to index like it used to, and in trial running (no work in chuck) an old practice program, the tool called for is not the one to index up(guess I may need to know how to do that,too). Anyway, when moving around axis's in manual mode, things seem fine, and 'home' mode goes back and lites come on; but when we run the practice program, the 'home' zero moves around on us(sometimes quite drastically). Repeated resetting of 'home' zero thru prameter 1815 has not got it to 'stay put'. Of course the Fanuc manuals take you just so far, and then refer you to your 'machine tool builder', NEAT!!! Any help would be GREATLY appreciated, Thanks howd.

[prabhat bhatera]

we have recently purchased okuma 7 howa act-3 we want english machine manual if you have please confirm we have manuals in german language.

[prabhat bhatera]

we have okuma & howa act-3 in manuals in german if you have in english please confirm.

[CNCMAINTENANCEA]

Dear All

RUN YOUR CNC MACHINE WITHOUT TROUBLE THIS IS FOR ONLY DELHI AND NCR CNC CUMMUNITY INDIAN CUSTOMER
WE ARE BASED IN DELHI FOR YOUR SERVICE

if your cnc machine is under breakdown and u want to start that

then contact == cncmainte@gmail.com

we work with all VMC ,DOUBLE COLUMN,HMC,turning cnc machine (imported one INDIA AND TAIWANI ) EQUIPED WITH BELOW MENTION CNC SYSTEM


FANUC ,MITSUBISHI,MAZAK,MELDAS,OKUMA OSP,SIEMENS,FAGOR


THANKS

[CNCMAINTENANCEA]

DEAR ALL

Originally Posted by CNCMAINTENANCEA Dear All THIS IS FOR ONLY DELHI AND NCR CNC CUMMUNITY INDIAN CUSTOMER WE ARE BASED IN DELHI FOR YOUR SERVICE if your cnc machine is under breakdown and u want to start that then contact == cncmainte@gmail.com we work with all VMC ,DOUBLE COLUMN,HMC,turning cnc machine (imported one only) EQUIPED WITH BELOW MENTION CNC SYSTEM FANUC ,MITSUBISHI,MAZAK,MELDAS,OKUMA OSP,SIEMENS,FAGOR THANKS

[prabhat bhatera]

how to set offset for 1st and 2nd tools for okuma & howa act 3 cnc lathe.

[Algirdas]

what kind of control has this ACT3? is it Okuma or Fanuc?

[Vu Tri Nhat]

please help me, I have one machine daewoo milling model ACE-V500

the machine have alarm No 2103 MUST BE COMMAND MANUAL ATC 1 CYCLE

i don't have any manual, if any body have manual maintennance book, please can send to me

Vu Tri Nhat

[Superman]

Vu,
Is your machine an Okuma ?
or a Daewoo ?

if it's a Daewoo
I don't think you will find a Kia part at a Toyota shop!!

[prabhat bhatera]

Originally Posted by Algirdas what kind of control has this ACT3? is it Okuma or Fanuc?

it is fanuc 10t control.