Need Help! OKUMA OSP-P200MA Control G83 change return point


Results 1 to 4 of 4

Thread: OKUMA OSP-P200MA Control G83 change return point

  1. #1
    Registered
    Join Date
    Jul 2016
    Location
    United States
    Posts
    10
    Downloads
    0
    Uploads
    0

    Default OKUMA OSP-P200MA Control G83 change return point

    I have looked but no success.

    What I am trying to do is change the point after it Rapids out and rapids back in, before it starts to feed again.
    Right now when it rapids back in the hole it rapids to .1 above the point of cut.
    What i want to do is to make it rapid to about .01 and start feeding again.
    Im sure there is a parameter like on a haas but i have no idea where i can find this.

    Thank you

    Similar Threads:


  2. #2
    Member
    Join Date
    Apr 2016
    Location
    United States
    Posts
    74
    Downloads
    0
    Uploads
    0

    Default Re: OKUMA OSP-P200MA Control G83 change return point

    in the okuma manual it talks about a parameter d1 and d2 to change the retraction point, might check that out.



  3. #3
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    4131
    Downloads
    0
    Uploads
    0

    Default Re: OKUMA OSP-P200MA Control G83 change return point

    hello as skywalker said, pls find attached manual pages

    ... d1 & d2 editable from nc_optional_para / fixed_cycles
    ... user_parameter for in_position ( check to be zero ) kindly !

    we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...


  4. #4
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    4131
    Downloads
    0
    Uploads
    0

    Default Re: OKUMA OSP-P200MA Control G83 change return point

    hmm ... try 0.3 .. 0.5mm, this should be 0.0118 .. 0.0196

    consider 0.02" ; you are too close at 0.01, and for what, to save a turn ?

    you would need the machine to accelerate, and at such low clearance you will succumb the cnc on big tools; this is the reason of the default parameter to be so great

    normally, consider 2.5mm as an upper limit, to cover most cases, thus 0.1"

    also you may consider a long hand code, so to avoid editing parameters

    we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...


  5. #5
    Registered
    Join Date
    Jul 2016
    Location
    United States
    Posts
    10
    Downloads
    0
    Uploads
    0

    Default Re: OKUMA OSP-P200MA Control G83 change return point

    Thanks found it in optional parameter.
    i dont know how i passed it over before when i was looking.

    i will do .02 rather safe then sorry.



  6. #6
    Member
    Join Date
    Apr 2016
    Location
    United States
    Posts
    74
    Downloads
    0
    Uploads
    0

    Default Re: OKUMA OSP-P200MA Control G83 change return point

    we have all work centers with a default of .030". haven't had any issues.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

OKUMA OSP-P200MA Control G83 change return point

OKUMA OSP-P200MA Control G83 change return point