Need Help! Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6


Results 1 to 3 of 3

Thread: Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6

  1. #1
    Registered
    Join Date
    Feb 2014
    Location
    United States
    Posts
    11
    Downloads
    0
    Uploads
    0

    Default Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6

    I've got an Okuma MC-4VA with a "201-Z Alarm A Servo Amp 2E6" alarm that I can't get it to reset.
    - There is a page for Alarm "201" "Alarm A", however I can't find anything about a "201-Z" or "Servo Amp 2E6".

    Opened up the rear box and there are no lights on on the Z-axis "BL-D(30)A" control board.

    There IS power going to the connectors from the DC-Power Supply board, regardless of whether the breaker to the right of the DC-PS is turned on or off.
    - However, the voltages do seem to vary once the breaker is turned off.

    According to the manual, if when the breaker to the DC-PS is turned off and the green light stays on, then the DC-PS needs replaced.

    A few questions that I can't seem to find through searches or the manuals:
    - If the DC-PS is bad, how is it still powering X & Y?
    - Is there a way to double check the DC-PS to know that's what is at fault?
    - Is there a fuse on the DC-PS that I should check?
    - Can a bad motor cause the above error?

    Similar Threads:
    Attached Thumbnails Attached Thumbnails Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170601_175934-jpg   Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170601_092954-jpg   Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170602_072650-jpg   Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170601_175944-jpg  

    Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170601_162722-jpg   Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170601_113300-jpg   Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170601_095156-jpg   Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6-20170601_174826-jpg  

    Last edited by treehick; 06-02-2017 at 03:04 PM.


  2. #2
    Registered
    Join Date
    Feb 2014
    Location
    United States
    Posts
    11
    Downloads
    0
    Uploads
    0

    Default Re: Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6

    Talked to a tech and they suggested that if the DC-PS had lights that it'd be the Z-axis drive.

    I had it quoted at something just under $5k. Checked on Ebay and found a Y-axis for around $700. All the numbers matched the Z-axis.

    I purchased and installed it and it's now currently running.

    Anyone know of any good places to repair the old drive?



  3. #3
    Member
    Join Date
    Aug 2012
    Location
    USA
    Posts
    164
    Downloads
    0
    Uploads
    0

    Default Re: Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6

    We do the BL-D series; we provide full 1 year warranty, all drives are fully tested in our simulators prior to being placed in inventory (for stock items) or returned to the customer (for repaired items). You can reach me at service@cnctechnical.com and I can provide you with repair/exchange details and cost. We can also provide full tech support on Okuma machines and controls.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6

Okuma MC-4VA - 201-Z Alarm A Servo Amp 2E6