turning works fine with G138 Y...
... but i can't measure tools ... i wish VBZOY was not readonly, or something
hello, please, i need an example for OD turning with double holders
Y axis changes between tools lb3oooex2 osp3oo
and how can i gauge those tools, since gauging with "Y on" fails ? kindly !
Similar Threads:
- Need Help!- C Axis Sample Code
- Anyone have sample Homing Code?
- Need Help!- Sample G-Code program
- Need Help!- Sample 5-axis NC code
- Asking for a G code sample
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
turning works fine with G138 Y...
... but i can't measure tools ... i wish VBZOY was not readonly, or something
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
hello again tea hole this code :Stop putting the machine in G138. Leave it in G136 ...
G136
T
Goo X0 Z2.5 Y9 > will not raise the Y, also there will be no errors
if i replace 6 with 8, than all will be ok works on my Y lathe
and when i remeber that it was you who showed me these VBZO* variables ; pls check attached image from the file shared in #1 : http://www.cnczone.com/forums/okuma/...able-list.htmlI don't believe there's any such thing as VBZOY
VBZOY shares same content as the base_o_offset_for_y_axis from system_para : if the value is edited inside the parameters, than the axis shift and i can measure the tools, but this involves editing the parameters, and that is a danger zone for the operators
if VBZOY was not read-only, than i could develop a faster way to shift the axis, like defining a G/M macro code
please, can you dig for this and share an example ? thcsOn the P200s it was a read/write variable ...
... i have tested a lot of variables, but not all
i can not raise the Y without the G138 kindly !in your programming you will not be in G138 for a Y axis tool either
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
yesteray i found a way to measure Y turning tools with 0.2 accuracy, but this involves some calculations
it does not take long, but is a bit longer than lowering the senzor and measuring the tools
this should be done once, at initial setup, because after that only inserts are changed, and only small corections take place ...
however, i am still looking for a normal way to do this, but i see this no longer as an obstacle; maybe my dealer will reply on that
now i am looking forward into merging this double Y holders with dynamic_indexing and offset_protection
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
hy hacdluxyou have to turn on the y axis to jog to centerline on the presetter
... Y offset <> 0
... Y axis ON
... T X Z Y0
... getting close to presetter
...... so far so good
if i turn off the Y axis / G136, than the turret will lower at Y0, and i won't be able do to the touchthen turn it off to do your touch. it will give you the ya xis not in turning pos alarm but will do the touch
if Y axis is ON, than i can't touch, because i receive the "Y on alarm"
Y axis will not move without G138 / kindly !i generally delete all g138's unless...
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
both of you : teahole & hacker_de_luxe told me to avoid G138
but i can not call the tool ( T X Y Z ) without G138
if you have the lb3000ex2 osp300, than maybe i am doing something wrong
if so, please, can you share a code example ? kindly !
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
this is how i measure X_offset for y_excentic tools :
1) OD / X+ / senzor upper edge / P8
... reset
... raise / lower the turret at specific Y value
... feed by hand until tool is in contact with senzor ; beep beep beep sound
... go at X_offset :
...... CALL : will input actual X value
...... ADD : -97.5
97.5 represent a diameter, where a corection with X_offset=0 is aligned with the upper edge of the senzor
"diameter" is materialized by the "X_axis_value"
"X_offset=0" is materialized by a "default id holder"
in other words : 97.5 is the value on my lathe were the "center axis" of the "id holder" is aligned with the "upper edge of the senzor"
this is represented in the attached images
2) ID / X- / senzor lower edge / P6
... same as above, only ADD value changes : -67.5
67.5 = 97.5 - 2 * 15, where 15 is the senzor edge ( the distance between upper and lower senzor edge )
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
this is how i measure Z_offset for y_excentic tools :
1) using a machined surface with known Z : if a knife machined a straight face ( Z=0 ), than call the tool and simply get close to that frontal;go in offset_menu, and press CALL inside Z offset + input 0 ( or the known Z value )
2) using a machine surface with known Z : the spindle frontal
3) using the senzor :
3.1) frontal / Z+ / senzor right edge / P7
... reset
... raise / lower the turret at specific Y value
... feed by hand until tool is in contact with senzor ; beep beep beep sound
... go at Z_offset :
...... CALL : will input actual Z value
...... ADD : VSZOZ - 212.870
212.87 is the distance between "spindle frontal" and "senzor right edge", as shown in attached image
3.2) reversed frontal / Z- / senzor left edge / P5
... same as above, only ADD value changes : VSZOZ - 197.870
197.870 = 212.870 - 15, where 15 is the distance between left and right edges of the senzor
... touch the senzor by feeding the wheel
... press CALL inside the offset_menu
... ADD a corection value
...... accuracy < 0.2
it may be an option to use the senzor while Y is active; i still wait for a response from my dealer
i insisted again today
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
hy hacdlux thank you for that sample, but it does not work 4 me ( attached images )
what are M101 and M102 for ?
please, will you share the content of "Ospmngcd.cnc" from your lathe ( c:\osp-p ) ? i wish to check the differences between lathes options; kindly !
ps : those images are clear, because i cleaned the control screen yesterday with a bit of coolant ...
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
hy hacker i will discuss again with my dealer next week
it has been a while since i started this thread, and meanwhile, the guy from the technical departement of our Okuma dealer left the country for 2-3 weeks
other guys are not so sharp, and i am tired of pointless discusions
at least i know that there is an "option" ; thank you
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
hello, please is it possible to use G33 with the turret raised on Y ?
... i bought tools with smaller shank ( square 20 )
... i bought Y holders + finish touches :
...... screws to have same length
...... screws to stick out of the holder more, and at same distance as my actual holders
...... some i_dont_know_the_word to dont clamp the tool shank directly
...... coolant pipes
... i have written the code for this double holders
but i can not put them on the machine, because there is a thread tool, and G33 is not workin with turret raised ... and dealer is frozen
please :
G97 S600 M3
G138
VTOFY[VETON] = -9
G00 X100 Z2.5 Y0
G33 X99 Z-50 F1
kindly !
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...
hy teahole, hy hacdlux, it took a while for my dealer to figure it out that the Y-turning option actually exists
we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...