Okuma OSP2200 LSN-10

[Russo1]

Hi

I bought a very old lathe. I'm trying to restore it to former glory and trying to get it into working shape. I am a IT specialist, so not much experience on lathes etc.

I do not have any diagrams of this lathe, nor any manuals. I've been searching and trying to find information (even pic's of working ones) and have not been succesfull.

I did decide that I won't use the tape reader and have bought a BTR.

I have a huge pile of cable, a hydraulic motor, cooling pump and the original "brain" box and the lathe.

I connected 380V 3 phase, and powered up, the hydraulics, nor cooling pump are connected. The console's lights came up. It said Out of tape or something similar. According to the guy who sold me the lathe, all the motors were tested and working.

Now this is to where I can take it.

Is there anybody that can help me. I can post pictures etc.

I will run this lathe on MasterCam XR2.

I will greatly appreciate, I've tried getting manuals, but at an average of $300 each, they're out my reach.

Thanx alot.

[Al_The_Man]

What control is on it? some Okuma's were fitted with Fanuc 6T. If it has Fanuc, do you have the parameters etc?
Al.

[mrainey]

When the time comes, I can help with OSP-2200 programming.

[Russo1]

I'm actually not sure. What I could get on the Net is that apparently Okuma started using Fanuc controllers a few models later.

I've looked on all the boards, which seem to be VME to find any information, to no avail. I also sent a ton of mail to Okuma/Fanuc to see if they can give my any info. The only thing I could get a name on is that it has a Sanyo Denki Tape Reader. The servo motors are Yaskawa.

Where can I look to see if it is Fanuc? I greatly appreciate your trouble. I'll take some photographs tommorrow and post them. If it can help....

Thanx a million

[Jarwalcot]

Here is a list of machine alarms that might help get you through the start up: http://www.homestead.com/mtsspecials...Alarm_List.pdf

Good Luck,

[Yupower]

i am so glade that i finally find something usefull on the internet that can help me to fix my problem.
it's been a long time since i buy my okuma lsn-10 osp-2200 lathe but almost 6 years i can't get this thing started
i buy this as a undamaged and in a good condition mashine that has work in a workshop in switzerland,but from the first start i know that something was not ok.
many peopels and professionals try to fix the problem but nothing happend
1 year after my father and i buy this mashine we make a decision to call switzerland and tell about the problem and we came to the final decision to bespeak the binary and the program tape from japan.
and anybody now what happends next :P
the tapes dont fix the problem
after that,we send the tape reader to switzerland and the say that the tape reader are intact.
we also try to program the osp2200 with the klik klak switches on the front table of the osp2200 and nothing happends
we also detect that the tape do not stop on the position he should and he wont stop until i press reset.
now i find mastercam x2 and predator dnc on the internet and i am not sure that this programs can fix my problem-i also have a rs-422 connector on the osp2200
i almost forget-on the main display are no error codes just sevens and nines on all lamps and they dont changes all 6 years
i have the complet user guide of this mashine and we try everything step by step but nothing
soo if anybody can halp me to fix my problem then please write in this treath and i will be the happiest man on the world really
PS-sorry for my english,i try my best

[Yupower]

have really nobody an answer for my question-please post if somebody can help me
thanx

[Jagermeister]

I have an okuma LS-N Big 10 sitting in sotage if you need a parts machine. Located in pennsylvania. Please get this thing out of here. LOL

[Yupower]

hehe jagermeister you are really funny
look at my profile and you will see were i live LOL
no really-in what a condition are your lsn-10 and have you the osp2200???
thanx

[Jagermeister]

The machine was in running condidtion when pulled from service. everything worked. It had a Mark Century 550 control.

[Yupower]

and why you wont to get your machine out of your sotage???
my lsn-10 is ok (i think so) what i need is a specialist who knows exactly what's wrong with my osp2200 or an elektrical shema
but thank you jagermeister for your offer

[rhino]

I have just printed this post out, i will have my OKUMA rep to have a look at it. then i'll let you know.