I am totally new to machining and to okuma. I have an okuma/crown 4020vmc. A person at my shop reloaded the software into the machine and now it reads my actual position as 625 x 637y and 650 z and will not let me jog or move the position. How do I get it to read the actual position correctly. (the machine was at home when he rebooted the software)
Check in the back of your machine for the Management Data card. It should have the encoder offsets recorded on it as well as the stroke end limits. Once those are set, you need to re enter your fixture offsets as well as your tool offsets etc.
Reloading software flushes all memory, so that is why it's highly recommended to back up first.
Newer controls do this automatically, older controls require a utility disk. Most all machines can at least use the data pip function to make a text file of the parameters , but saving the PBU files with the utility is the best way.
Best regards,
Thank you for the answer. This probably sounds really dumb but I don't know where to enter the encoder offsets and the stroke end limiets. I do have a backup card which has bpu parameters saved by the previous owner but I do not know how to load them. How can I do that?
You'll need to go into your PARAMETER mode and then ITEM down until you get to SYSTEM PARAMETERS. You should find your encoder offset listed as PR ZERO OFFSET and your STROKE END LIMITS should be on the same page if I remember right.
Press SET then enter the numbers followed by WRITE. (record old numbers first incase you make a mistake) You should get an alarm that says" Power on effective parameter set" at that time. Enter all of your numbers, press the BACKUP key and then power off and on your control.
If all goes well, your machine will be able to jog between it's limits once again.
Best regards,
thank you again, I will let you know how it goes. Just for my education, how can I load the from the back up disc? How do I call them up from the disc and save them to the memory?
there are at least two ways.
1. Use maintenance mode. It's switch on the CPU inside main control cabinet.
2. save parameters into file in regular working mode with DPIP.
thank you, can you help walk me through it on the control?
Okumawiz and Algirdaz thank you. I was able to load the parameters again. The actual position is now correct.
However, I still cannot get the axis to jog (any of them) It shows no alarms and no problems, they just don't move. Any suggestions?
Double check your STROKE END LIMITS and VARIABLE LIMITS are correct and that you are "within" your limits. If you are, check to make sure your ATC is on #1 with READY displayed. Sometimes if it is not, it will lock axis movement.
Best regards,
I adjusted the variable limits and am within the stroke end limits. The atc is in position 1 and ready. I can now jog x but there is still no movement on z or y. Any suggestions?
Are there any axis inhibits on? Are by chance the positive and negative numbers swapped in the limits? Do the numbers for the limits based on your zero set "look correct" in the ACTUAL POSITION (program) display?
I'm kind of guessing in the dark here without any actual numbers of what the position is and what your VARIABLE LIMIT numbers are, so that may be a next step. Let us know some more details if possible.
Best regards,
PS> No pallet changer on this machine, right?
p program work limit x=20 y=9.0945 z = 17.5590
nprogram work limit x= -20 y= -90945 z = - .390
mc is the same
system parameter
p travel limit x= 20n n y = 9.0945 z= 17.559
n travel limit x = -20 y =-9.0945 z= -.0390
actual position x = -5.5991 y = 5.5997 z= 17.4893
this is my position. Below are the two alarms I have seen.
alarm earlier (2713 axis interlock releasing )
alarm when trying atc ( 3705 atc system condition 380)
I have not been able to see the page in user parameter for axis interlock. I select it but it does not appear
Posting Permissions
LinkBack URL
About LinkBacks
