OKK Milcon III with MELDAS 83A

[parametric.ms]

I just bought an old machine with totally dead condition. But the controller inside the panel still looks good (so far looks original). Before I decided to retrofit, I'd like to make sure that machine still can be repaired. But I have problem, because the battery has lost.

Does anyone have paramater description for MELDAS 83A?

[DPL86]

hy,

i have an okk mcv-300 with meldas 84.
i think it is the same controler.
send-me an e-mail i
i will send you my parameter (from my working machine...).
regards
den.

[mosesooi]

Hi,
Do any1 of u guy have manual for Mitsubishi Dc servo TRA6oC ?

[parametric.ms]

Hi,
Do any1 of u guy have manual for Mitsubishi Dc servo TRA6oC ?

Have you try meau.com? I got it from there, but I can't find for MELDAS 83A manual.
btw, what is your controller? is it MELDAS 83A? do you have copy of parameter list?

[mosesooi]

Hi,
Yes the controller is Meldas 83A,With all Parameters in.Controller out,Tra60 Drive Manual
needed so that i can change to other Controller.May Be other brand!.Don't too hopeful
to meau.com,they care about New Products only!!!

[parametric.ms]

Have you check it on meau carefully?????
http://www.meau.com/Files/BNP-A6478.PDF <== TRA30 & TRA60

Now, whats a problem with your controller?? I can't find a way how to write parameter on it. Seems to locked by keyword or jumper setting on MELDAS 83A. Any clues?

[mosesooi]

parametric,
The Password Is PS In First Line.

[mosesooi]

parametric,
thanks for your reply,but fail to connect the site.Should I register first? Where & How??

[parametric.ms]

check your PM

[parametric.ms]

http://www.meau.com/eprise/main/site...e=&ManualType=

Find the filename that I give on the site

[genem]

Is there anyone available that currently has manuals to a meldas 84 control?

[mosesooi]

parametric.ms.
Hi Andre,
Okk Is A Good Machines But Not Meldas 83A!
I Don't Think You Can Run M99 In Your Machine.
All Limited M Code And G Code Is Stated In The Side Of The Main Panel.(Which Contains
The Meldas 83A ).Please Keep In Mind, Your MC Is An NC Not CNC!!!
Any How I Will Give You All The ParameterS You Need:

S1 +0 +120
0 120
0 160
0 0
1 8000
0 8000
70 6000
100 0

CF +4000 +2
4000 2
4000 2
0 0
20 0
20 0
7 0
0 0

BR +4 +6400
5 6400
0 4800
0 0
0 0
0 0
0 0
0 0

T1 +5 +7
5 3
10 10
3 30
3 60
3 5
7 20
7 7

D1 +0 +2308
0 2308
0 2504
0 0
0 11
0 10
0 8
0 0

P1 -8901 -601
8601 401
8401 1011
7601 3950
6601 3850
2601 3451
1601 3051
901 2251

P17 -1951 -2251
1851 1851
1701 1450
7511 650
6511 250
4251 +0
3850 +0
3451 +0

FX1 +0 -921000
0 -401000
1000 -471000
1000 +0
300 0
300 0
300 0
0 0