hy,
i have an okk mcv-300 with meldas 84.
i think it is the same controler.
send-me an e-mail i
i will send you my parameter (from my working machine...).
regards
den.
I just bought an old machine with totally dead condition. But the controller inside the panel still looks good (so far looks original). Before I decided to retrofit, I'd like to make sure that machine still can be repaired. But I have problem, because the battery has lost.
Does anyone have paramater description for MELDAS 83A?
Similar Threads:
- Meldas 60
- For MELDAS 300 PLC
- Need Help!- MELDAS 83A
- Meldas-m60
- meldas 500
hy,
i have an okk mcv-300 with meldas 84.
i think it is the same controler.
send-me an e-mail i
i will send you my parameter (from my working machine...).
regards
den.
Hi,
Do any1 of u guy have manual for Mitsubishi Dc servo TRA6oC ?
Hi,
Yes the controller is Meldas 83A,With all Parameters in.Controller out,Tra60 Drive Manual
needed so that i can change to other Controller.May Be other brand!.Don't too hopeful
to meau.com,they care about New Products only!!!
Have you check it on meau carefully?????
http://www.meau.com/Files/BNP-A6478.PDF <== TRA30 & TRA60
Now, whats a problem with your controller?? I can't find a way how to write parameter on it. Seems to locked by keyword or jumper setting on MELDAS 83A. Any clues?
parametric,
The Password Is PS In First Line.
parametric,
thanks for your reply,but fail to connect the site.Should I register first? Where & How??
check your PM
Find the filename that I give on the site
Is there anyone available that currently has manuals to a meldas 84 control?
parametric.ms.
Hi Andre,
Okk Is A Good Machines But Not Meldas 83A!
I Don't Think You Can Run M99 In Your Machine.
All Limited M Code And G Code Is Stated In The Side Of The Main Panel.(Which Contains
The Meldas 83A ).Please Keep In Mind, Your MC Is An NC Not CNC!!!
Any How I Will Give You All The ParameterS You Need:
S1 +0 +120
0 120
0 160
0 0
1 8000
0 8000
70 6000
100 0
CF +4000 +2
4000 2
4000 2
0 0
20 0
20 0
7 0
0 0
BR +4 +6400
5 6400
0 4800
0 0
0 0
0 0
0 0
0 0
T1 +5 +7
5 3
10 10
3 30
3 60
3 5
7 20
7 7
D1 +0 +2308
0 2308
0 2504
0 0
0 11
0 10
0 8
0 0
P1 -8901 -601
8601 401
8401 1011
7601 3950
6601 3850
2601 3451
1601 3051
901 2251
P17 -1951 -2251
1851 1851
1701 1450
7511 650
6511 250
4251 +0
3850 +0
3451 +0
FX1 +0 -921000
0 -401000
1000 -471000
1000 +0
300 0
300 0
300 0
0 0
Thanks a lot for replying my message.
But I still don't get it how to make a rewind program in okk
My control contain with this :
1. Circular Interpolation
2. Radius Programming on Arc
3. Simultanous 3 Axis Linear Interpolation
4. Return to Zero
5. High Speed Return to Zero
6. Mechanical Handle
7. Rapid Traverse Override
8. Stroke Check
9. Additional Tool Offset 32 Set
10. Cutter Radius Offset
11. Canned Cycle
12. Memory Type Pitch Error Compensation
13. Auto Restart
14. Decimal Point Program
15. Program Number Search
16. Tape Store 10m Edit
17. Sub Program Function
18. External Operation Board
19. Built in Sequencer
20. Built in Machine Operation Panel
21. Xxxxx (kanji fonts)
22. Tape Punch / Print Out I/F
I have no idea how to activate the option parameter. Should I try one by one with hexadecimal configuration?
How about yours? Is it same optional with mine?
Sorry if I disturb you recently.
Regards,
Andre
I have two machine of OKK Millcon III (MHA 400 & MHA 300). Both has Meldas 83A controller
The machine when bought was not in running condition and was idle for a while
I tried to power up the machinery
Both displays the same alarm E=20 when i try to power on the machine and release the emergency
Moreover I tried to change the parameter which wasn't successful at all
I have been told that it's a software related emergency parameter
I'm not convinced with the reply
I'm open to suggestions
If needed I can send screenshots
P.S. I have the original parameters. But i would like to know the parameter setting procedure. Because however we do it, we couldn't change the parameters other than the M list
Kindly assist
I have two machine of OKK Millcon III (MHA 400 & MHA 300). Both has Meldas 83A controller
The machine when bought was not in running condition and was idle for a while
I tried to power up the machinery
Both displays the same alarm E=20 when i try to power on the machine and release the emergency
Moreover I tried to change the parameter which wasn't successful at all
I have been told that it's a software related emergency parameter
I'm not convinced with the reply
I'm open to suggestions
If needed I can send screenshots
P.S. I have the original parameters. But i would like to know the parameter setting procedure. Because however we do it, we couldn't change the parameters other than the M list
Kindly assist