Metal Working Tooling


Page 1 of 9 1234 ... LastLast
Threads 1 to 20 of 165

Forum: Metal Working Tooling

Tooling specific to Metal Working

  1. Screw Tangs for MT2 or general MT Shank

    Started by al010964‎, 07-08-2017 10:19 PM
    • Replies: 5
    • Views: 277
    07-14-2017, 10:50 PM Go to last post
  2. ID Grooving tool help!

    Started by kdupreez‎, 03-17-2017 02:23 PM
    • Replies: 9
    • Views: 680
    07-11-2017, 06:13 PM Go to last post
  3. When to change a grinding wheel?

    Started by Cobra92fs‎, 02-15-2017 12:59 PM
    change, cnc, grinding, speed, wheel
    • Replies: 3
    • Views: 428
    02-16-2017, 11:05 AM Go to last post
  4. Best material choice fornew QCTP?

    Started by smarrocco‎, 10-20-2016 10:22 AM
    cnc, column, diameter, sherline, steel
    • Replies: 0
    • Views: 602
    10-20-2016, 10:22 AM Go to last post
  5. Boring Head need help

    Started by truckeic‎, 10-10-2016 02:09 PM
    cnc, mill, pocket, correct, head
    • Replies: 0
    • Views: 354
    10-10-2016, 02:09 PM Go to last post
    • Replies: 1
    • Views: 374
    09-17-2016, 11:02 AM Go to last post
  6. Looking for a good online slot drill seller??

    Started by chucka103‎, 04-03-2016 08:45 AM
    display, good, online, searching, slot
    • Replies: 0
    • Views: 999
    04-03-2016, 08:45 AM Go to last post
  7. Problem- E32 collet not enough for 5/8 end mill in steel?

    Started by jdholbrook‎, 03-17-2016 07:36 PM
    2 Pages
    1 2
    5/8, collet, end, mill, steel
    • Replies: 12
    • Views: 1,208
    03-28-2016, 07:22 PM Go to last post
  8. Insert size deviations from specs

    Started by myhäje‎, 03-27-2016 02:22 AM
    deviation, diameter, insert, kind, millimeters
    • Replies: 0
    • Views: 415
    03-27-2016, 02:22 AM Go to last post
  9. Question Newbie- ER11 spanners

    Started by STEPHENPRESCOTT‎, 02-17-2016 09:47 AM
    • Replies: 4
    • Views: 769
    02-18-2016, 08:36 AM Go to last post
  10. metalworking tools for sell

    Started by plovdivtransmetal‎, 12-30-2015 06:08 AM
    • Replies: 1
    • Views: 520
    01-05-2016, 06:36 AM Go to last post
  11. Need Help!- Need help aluminium cut

    Started by assadi‎, 12-18-2015 04:16 PM
    2 Pages
    1 2
    • Replies: 20
    • Views: 2,016
    12-31-2015, 04:19 PM Go to last post
  12. Custom Motor

    Started by gicos‎, 12-19-2015 08:36 AM
    motor, plates, posts, press, shaft
    • Replies: 2
    • Views: 638
    12-19-2015, 10:39 AM Go to last post
  13. 1/2-14 NPTF thread

    Started by Rock09‎, 06-18-2015 10:56 AM
    1/2-14, insert, material, nptf, thread
    • Replies: 0
    • Views: 1,666
    06-18-2015, 10:56 AM Go to last post
  14. Question Need Help!- Looking for a chuck for my uncle-in-law

    Started by flyingrizzly‎, 06-07-2015 02:38 PM
    chuck, lathes, machinist, wanted, years
    • Replies: 0
    • Views: 819
    06-07-2015, 02:38 PM Go to last post
  15. need advice on super duplex

    Started by fnoldguy‎, 05-01-2015 08:57 PM
    duplex, mill, rough, super, tools
    • Replies: 0
    • Views: 946
    05-01-2015, 08:57 PM Go to last post
  16. end mill life question

    Started by bbutcher85710‎, 07-01-2014 01:10 AM
    032, available, maybe, next, plus, since, then, within
    • Replies: 4
    • Views: 2,066
    01-11-2015, 09:36 PM Go to last post
  17. Need Help!- Using a louvre tool for Amada CNC Fanuc

    Started by Weingold‎, 03-08-2011 02:22 AM
    since
    • Replies: 1
    • Views: 3,246
    01-03-2015, 04:52 PM Go to last post
  18. Need Help!- "Face milling" with end mills (workpiece is smaller than end mill dia.)

    Started by hav0c‎, 07-13-2014 06:11 PM
    another, down
    • Replies: 3
    • Views: 1,345
    12-23-2014, 08:13 PM Go to last post
  19. reamer most precise tool holder

    Started by allenp‎, 12-21-2014 08:50 AM
    0.0, 0.05mm, 5mm, beall, car, higher, holder, html, http, ion, precise, reamer, solution, speeds, tendency, tha, tool, tool holder, typically, url, wha, www
    • Replies: 0
    • Views: 908
    12-21-2014, 08:50 AM Go to last post

Page 1 of 9 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands