Need Help!- Sample G-Code program

[tward74]

Does anyone have a sample G-Code program for a T-2 controller? I am not great with programming Mazatrol, but I am pretty good with G-Code programming. I would like to start sending programs to the lathe to make my programming time decrease.

[Perfect Circle]

I can post you some code for a mazatrol t-32

[Perfect Circle]

Here is a rough and finish turning cycle on the OD

%
O00001 ( PROGRAM NUMBER )
( PROGRAM START - TURNING CYCLES )
( PROGRAM NAME: CNCZONE.NC)
( POST: MAZATROL T32 )
( DATE: THU. 12/02/2010)
( TIME: 09:11AM)
N01 G98 G90 G80 G40 G20
N02 G00 G28 U0. W0.
(JOB 1 ROUGH CYCLE )
(TOOL #1 80 DEG. 1/64 ROUGH TURNING )
N03 G54 G97 S477 T0101 M04
N04 G50 S400
N05 G96 S400
N06 G00 X1.6 Z.3 M08
N07 X1.3
N08 G01 Z-3. F.01
N09 X1.4 F.01
N10 G00 Z.3
N11 X1.1
N12 G01 Z-3. F.01
N13 X1.2 F.01
N14 G00 Z.3
N15 X1.02
N16 G01 Z-3. F.01
N17 X1.12 F.01
N18 G00 X5.
N19 Z5.
N20 G40
N21M09
N22 G97
N23 T0100
N24 M01
N25M09
N26 G00 G28 U0. W0.
(JOB 1 ROUGH CYCLE )
(TOOL #2 80 DEG. 1/64 FINISH TURNING )
N27 G54 G97 S746 T0202 M04
N28 G50 S400
N29 G96 S400
N30 G00 X1.6 Z.3 M08
N31 X1.
N32 G01 Z0. F.006
N33 Z-3. F.006
N34 X1.1 F.006
N35 G00 X5.
N36 Z5.
N37 G40
N38M09
N39 G97
N40 T0200
N41 M01
N42 M05
N43 G28 U0. W0.
N44 M30
%

I can do more operations if you need ...also canned cycles
Hope this helps, IF not let me know.

[tward74]

i know they are going to ask me for the canned cycles as well. i am trying to get a post processor from Bobcad. So if it isn't a huge undertaking, could you please send me a program with drilling cycle and tapping cycle if you have it. Thanks so much for the help!!

[Perfect Circle]

Here is the same sample part with canned cycles for a Mazatrol T32

%
O00001 ( PROGRAM NUMBER )
( PROGRAM START - TURNING CYCLES )
( PROGRAM NAME: CNCZONE.NC)
( POST: MAZATROL T32 )
( DATE: THU. 12/02/2010)
( TIME: 01:45PM)
N01 G98 G90 G80 G40 G20
N02 G00 G28 U0. W0.
(JOB 1 ROUGH CYCLE )
(TOOL #1 80 DEG. 1/64 ROUGH TURNING )
N03 G54 G97 S509 T0101 M04
N04 G50 S400
N05 G96 S400
N06 G00 X1.5 Z.3 M08
N07 G71 U.2 R.1
N08 G71 P09 Q11 U.02 W.01 F.01
N09 G00 X1.
N10 G01 Z-3. F.01
N11 X1.1 F.01
N12 G40
N13M09
N14 G97
N15 T0100
N16 M01
N17 G00 X5. Z.3
N18 Z5.
N19M09
N20 G00 G28 U0. W0.
(JOB 1 ROUGH CYCLE )
(TOOL #2 80 DEG. 1/64 FINISH TURNING )
N21 G54 G97 S509 T0202 M04
N22 G50 S400
N23 G96 S400
N24 G00 X1.5 Z.3 M08
N25 G28 U0. W0.
(TOOL #2 80 DEG. 1/64 FINISH TURNING )
N26 G54 G97 S795 T0202 M04
N27 G50 S400
N28 X1. Z.3 M08
N29 G96 S625
N30 G70 P09 Q11 F.006
N31 G40
N32M09
N33 G97
N34 T0200
N35 M01
N36 G00 X5.
N37 Z5.
N38 M05
N39 G28 U0. W0.
N40 M30
%

Ill work on getting the others asap...ehh and good luck with BobCad ....

[Perfect Circle]

Here is a 1.00 hole and a threaded OD of 2"-12 tpi..
Good luck with building your post. If I can help you any more just let me know.

%
O00001 ( PROGRAM NUMBER )
( PROGRAM START - TURNING CYCLES )
( PROGRAM NAME: CNCZONE.NC)
( POST: MAZATROL T32 )
( DATE: THU. 12/02/2010)
( TIME: 01:53PM)
N01 G98 G90 G80 G40 G20
N02 G00 G28 U0. W0.
(JOB 1 DRILLING CYCLE )
(TOOL #7 1.000 dia )
N03 G54 G97 T0707 M04
N04 G50 S400
N05 G97 S400
N06 G00 X0. Z.1 M08
N07 G74 R.1
N08 G74 X0. Z-3. I0. K.2 R0. F.01
N09M09
N10 G97
N11 T0700
N12 M01
N13 G00 Z5.
N14 X5.
N15M09
N16 G00 G28 U0. W0.
(JOB 2 THREAD CYCLE )
(TOOL #4 60 DEG. 1/8 0.003 RADTHREADING )
N17 G54 G97 T0404 M04
N18 G50 S400
N19 G97 S400
N20 G00 X1.05 Z0. M08
N21 G01 X1. F.0833
N22 G76 Q030060 U.03 R.001
N23 G76 X.9278 Z-3. K0721 D0500 F.083333
N24 G00 X5.
N25 Z5.
N26 G40
N27M09
N28 G97
N29 T0400
N30 M01
N31 M05
N32 G28 U0. W0.
N33 M30
%

[tward74]

Thank you Perfect circle for the programs. I am going to try and send these to the Mazak and see if it works and then see if BobCAD can get me a post processor.