| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| Mastercam Discuss Mastercam software here. |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#13
08-01-2008, 10:40 PM
| ||||
| ||||
| yongchiprsnapr,Please review my picture for some settings. Mike I am sorry you did not like my reply. but by chance did you review my video as I showed how it works and that the Auto curser does not effect it. I know I did it in X3 but it has not changed in the last few years. Oooppss that was suppose to be "Quick Note" on my picture.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng)  |
|
#14
08-01-2008, 10:45 PM
| ||||
| ||||
| Just tried it in MCX MR1 this is the MR release after MCX release. Works the same.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
|
#15
08-01-2008, 10:48 PM
| |||
| |||
| I never said I did not like your reply. I have no problem with that feature in any version. |
| Sponsored Links |
| |
|
#16
08-09-2008, 05:28 PM
| |||
| |||
| well, i finally took my computer over to the other plant. went down their configuration settings copying them exactly. now it works as easily as it should. dont really know which one was the problem. im just happy its working now. i was afraid the computer was too slow to run 10 or something. didnt want to learn 9.thanks Mike S., cadcam, Mike M., and anyone else who posted in the thread offering help. if already got another question lol. later |
|
#17
08-09-2008, 05:40 PM
| ||||
| ||||
| I am glad to hear all is good. and that all of us were help some were.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) Last edited by cadcam; 08-09-2008 at 06:14 PM. |
|
#18
08-09-2008, 05:59 PM
| |||
| |||
| I am so glad you were able to fix the problem. |
|
#19
11-30-2008, 04:39 PM
| |||
| |||
Tangents to two arcs are no problem for me. However, I cannot figure out how to draw a tangent to a circle and to a spline or a tangent to two ellipses, etc. Any one have a tip for drawing a tangent to two curves that are not arcs? |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| points to lines/arcs | vmax549 | Autodesk Software (Autocad, Inventor etc) | 7 | 10-14-2008 08:05 AM |
| line tangent from... | Castle1 | Rhino 3D | 1 | 09-20-2007 08:08 PM |
| lines-arcs vs spline problem | metlcutr55 | General CAM Discussion | 1 | 07-07-2006 10:16 AM |
| tangent point | bob in windsor | General Metalwork Discussion | 11 | 12-23-2005 03:05 PM |
| Lines and Joining them | scottsss | Rhino 3D | 5 | 07-29-2003 05:41 AM |
| | |
Tangent to two curves not arcs 
Linear Mode
