Hi,
I have a AB 9/240 controller on a EXCELLO verticle mill and need to modify the MPFAN postprocessor that Mastercam supplies you with.
Can someone walk me through some mods I need?? Or is it too difficult?? I have tried numerous times with no success..
Such things like I have no line numbers.. Can't find where you would put them in.
I have posted this in the POST forum also..
Thanks for any help
Line numbers are a switch. Look forand change it to 0 instead of 1Code:omitseq : 1 #Omit sequence no.
Lots of the basic stuff is right there, just switches you toggle on or off. There's pretty good descriptions of what they do with them.
Feel free to as any other questions you might have, I've got MP running thru meh veins.
'Rekd
Matt
San Diego, Ca
___ o o o_
[l_,[_____],
l---L - □lllllll□-
( )_) ( )_)--)_)
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Rekd, I tried to switch the yes/no statement to a "1". I still get no line numbers.. Not even the begining "N". If I put in a "0" I get "N0" at the begining of each line.. I also tried other numbers with the same results... No line numbers, just coordinates..
I guess I need to get that CD from my dealer..
Thanks again for any help..
What version of MC? Can you send me a copy of the post and a copy of the code THE WAY YOU WANT IT?
Matt
San Diego, Ca
___ o o o_
[l_,[_____],
l---L - □lllllll□-
( )_) ( )_)--)_)
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
BTW, omitsiq = NO does leave them turned on. You might try just commenting out that whole line. (Put a pound sign in front of it.. " # " )
'Rekd
Matt
San Diego, Ca
___ o o o_
[l_,[_____],
l---L - □lllllll□-
( )_) ( )_)--)_)
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Yes, I will send you a copy of the post and a copy of my program the way I would like it..
Thanks again
pete
Your welcome.
Matt
San Diego, Ca
___ o o o_
[l_,[_____],
l---L - □lllllll□-
( )_) ( )_)--)_)
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Should I post it here?? Or send email??
Thanks
Send it mail, I want the complete post so I can run it thru my machine. I'll post what I find here.
Matt
San Diego, Ca
___ o o o_
[l_,[_____],
l---L - □lllllll□-
( )_) ( )_)--)_)
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
You should be all set with this, Pete. Open your post and change this line
To this.Code:seqmax : 2 #Max. sequence number
Make sure you leave "omitseq" set @ "0"Code:seqmax : 9999 #Max. sequence number
I posted a file right from the original post and got
N1
N2
N1
N2
etc.
By changing "seqmax" to 9999 it will go from N1 to N9999 then restart at N1 again. If your controller supports more/less than that, you can change it.
Also, read thru the text towards the top of the post, it may guide you to making more simple changes. Just back up your original first.
HTH, and if you have more ?'s or !'s let me know.
'Rekd
Last edited by Rekd; 05-26-2004 at 11:16 AM.
Matt
San Diego, Ca
___ o o o_
[l_,[_____],
l---L - □lllllll□-
( )_) ( )_)--)_)
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Rekd,
I did exactly as you said and no dice.. I went back to the original MPFAN.PST and guess what.. No line numbers.. All I get is..
N0 X???
N0 Y??
N0..Z??
The settings in my original MPFAN post are just what you told me to do to my modified post..
"seqmax : 9999 #Max. sequence number"
Think maybe something else is wrong??
Thanks again for all your time and patience
Pete
Oh ya this is located in the "general output settings" paragraph correct??
Thanks
Posting Permissions
LinkBack URL
About LinkBacks
