| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| Mastercam Discuss Mastercam software here. |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#1
 
01-16-2007, 03:41 PM
| |||
| |||
So, I just got my new Dell Dimension today. Everything's going great until I go to plug my hasp in and find that while it has plenty of USB ports, it DOESN"T HAVE A PARALLEL PORT! Is there anyway to make this HASP work with a USB port or am I stuck having to crack the case on my brand new Dell and install a parallel port?
__________________ I don't know much about anything but I know a little about everything....    |
|
#2
01-16-2007, 03:48 PM
| ||||
| ||||
| Yeah, a lot of the new computers dont come with a parallel port...  |
|
#3
01-16-2007, 05:22 PM
| ||||
| ||||
| You might want to ask your reseller how much it costs to switch to a USB hasp... |
|
#4
01-16-2007, 07:41 PM
| ||||
| ||||
| Matt there would be a small cost unless his Key is Hasp3. cdlenterprises what version are you running by chance?
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
|
#5
01-16-2007, 07:51 PM
| ||||
| ||||
| [hijack] Hi Jay, how's it going ? [/hijack] |
| Sponsored Links |
| |
|
#6
01-16-2007, 07:57 PM
| ||||
| ||||
| Matt, Not bad trying to get a good start for the new year and you?
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
|
#7
01-16-2007, 08:07 PM
| ||||
| ||||
| Pretty good, thanks... I'm still trying to catch up with last year... LOL |
|
#8
01-16-2007, 08:16 PM
| ||||
| ||||
| Well Power user Matt, I am with you still playing the same way at work and home.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
|
#9
01-17-2007, 07:06 AM
| |||
| |||
| I'm still running version 9. I'm not sure what version the hasp is. I'll most likely end up installing a port into it. I'm sure it will come in handy.... 
__________________ I don't know much about anything but I know a little about everything.... |
|
#10
01-17-2007, 09:24 AM
| ||||
| ||||
| Well in that case go to www.simswap.com and download Haspinfo it will test the hasp to see if you can swap it for free to a Hasp4 if it is a hasp3 and they will send you a USB key. As for neededing a Parriall port I don't see it unless your printer is.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
| Sponsored Links |
| |
|
#11
01-17-2007, 06:14 PM
| ||||
| ||||
| Jay, Would you happen to know why I am now a power user ? Is this some special privilege being extended to me or what...  I was actually wondering how Toby got to be the Evil Machinist recently... |
|
#12
01-17-2007, 10:47 PM
| ||||
| ||||
| Would you happen to know why I am now a power user ?) Actully I do know. I made you it.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
| | |
Linear Mode
