| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| Mastercam Discuss Mastercam software here. |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#1
 
08-27-2003, 09:59 PM
| ||||
| ||||
| efficient tool path Hi, Why is it, that when I do a pocket with some islands, for example this harley logo, the tool path isn't very efficient, as in the tool goes all over the place, and often over the same spot a few times and jumps around a lot. I chose the default pocketing method (zigzag). I tend to leave other check marks etc. at the default as well, as usually I don't know what they mean...  Forgive me as I am a poor Mastercam user, because I am trying to teach myself. The factory I work at has mastercam (one seat), which the tool and die makers use, and I try to get on it when I can. I am just an electricain. Try to be patient. Eric
__________________ I wish it wouldn't crash.    |
|
#4
08-27-2003, 10:58 PM
| ||||
| ||||
|
__________________ I wish it wouldn't crash. |
|
#7
08-28-2003, 01:10 AM
| ||||
| ||||
| balsaman, were should I put the file on the ftp.. I will Zip it and it's you file with jay added to it and a single op.
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
|
#8
08-28-2003, 01:10 AM
| ||||
| ||||
| Look on the FTP under Mastercam_Files
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Cadcam Mastercam Instructor , Programming Consultant and ME (Manufacturing Eng) |
|
#9
08-28-2003, 04:30 PM
| ||||
| ||||
I can't access the FTP site. Send it to my email. cnchomeman@yahoo.com Thanks Eric
__________________ I wish it wouldn't crash. |
|
#11
08-28-2003, 09:15 PM
| ||||
| ||||
| Are you behind a firewall?
__________________ Matt San Diego, Ca ___ o o o_ [l_,[_____], l---L - □lllllll□- ( )_) ( )_)--)_) (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Laser tool path display....( IDEA ) | ynneb | DIY-CNC Router Table Machines | 41 | 04-10-2006 11:19 PM |
| tool path problem | fastolds | BobCad-Cam | 9 | 07-07-2005 01:01 PM |
| getting tool path problem | kenlambert | BobCad-Cam | 0 | 01-14-2005 03:15 PM |
| tool path generation BobCAD V18/19 | inthedark | BobCad-Cam | 3 | 02-10-2004 10:14 PM |
| Tool Path | WOODKNACK | TurboCAD/CAM | 4 | 06-27-2003 08:27 AM |
| | |
Linear Mode
