Maintenance DIY Discussion

Page 1 of 18 1234 11 ... LastLast
Threads 1 to 20 of 351

Forum: Maintenance DIY Discussion

Discuss anything from how to install a simple light fixture, wiring sub panels, shop air, water, vacuum etc

  1. Best Dust Collection System for Fab Lab?

    Started by thinktankgroup‎, 07-11-2017 12:30 PM
    • Replies: 0
    • Views: 122
    07-11-2017, 12:30 PM Go to last post
    • Replies: 0
    • Views: 26
    07-11-2017, 11:14 AM Go to last post
  2. Lightbulb Need Help!- Hiding Dust in Fabrication Lab - Paint Advice

    Started by thinktankgroup‎, 07-10-2017 11:04 AM
    fab lab, fabrication lab, kuka, makerspace, paint
    • Replies: 0
    • Views: 95
    07-10-2017, 11:04 AM Go to last post
  3. Step up transformers and amp draw

    Started by rdnck68‎, 06-30-2017 11:07 AM
    machine, panel, transformer, step, amp
    • Replies: 10
    • Views: 301
    07-08-2017, 03:17 PM Go to last post
  4. Vacuum belt?

    Started by Johnauto‎, 04-21-2017 10:44 PM
    belts, issue, normal, vacuum, work
    • Replies: 1
    • Views: 521
    04-22-2017, 06:15 AM Go to last post
  5. Need Help!- HSD ES919 Spindle bearing removal help..

    Started by Stepping3D‎, 10-30-2016 03:09 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 1,497
    04-19-2017, 05:23 AM Go to last post
  6. Hydmech saw vw18

    Started by JKGONZAL‎, 04-17-2017 03:35 PM
    changed, errors, jaws/clamps, move, vw18
    • Replies: 0
    • Views: 96
    04-17-2017, 03:35 PM Go to last post
  7. Newbie- Stones for CNC table upkeep

    Started by RedneckPhysics‎, 03-31-2017 09:26 AM
    cnc, find, high, spots, tormach
    • Replies: 1
    • Views: 226
    04-09-2017, 07:18 PM Go to last post
  8. Problem- Is it possible to disassemble/reuse these Heidenhain connectors?

    Started by BMcCaskill‎, 03-20-2017 11:04 PM
    check, cut, http://imgur.com/1vgaaej, http://imgur.com/iytfsyl, wanted
    • Replies: 5
    • Views: 366
    03-27-2017, 03:39 PM Go to last post
    • Replies: 2
    • Views: 280
    02-24-2017, 08:09 AM Go to last post
  9. Need Help!- Mazak VTC200b X Axis linear bearing blocks

    Started by kentw‎, 02-09-2017 04:07 PM
    axis, blocks, linear, mazak, vtc200b
    • Replies: 0
    • Views: 292
    02-09-2017, 04:07 PM Go to last post
  10. Question Brother TC-228 Screen not working

    Started by tthayer‎, 12-09-2016 09:52 AM
    brother, brother cnc, cnc, electrical, repair
    • Replies: 2
    • Views: 473
    01-09-2017, 11:39 AM Go to last post
  11. Magnet for hand held Pendant

    Started by Deming‎, 12-10-2016 10:21 PM
    50lb, comments, magnet, pendant, suggestion
    • Replies: 0
    • Views: 207
    12-10-2016, 10:21 PM Go to last post
  12. Best air and suction hoses for routers

    Started by SandlilyMarkos‎, 12-09-2016 09:05 AM
    flex, good, hoses, routers, suction
    • Replies: 4
    • Views: 320
    12-10-2016, 04:43 AM Go to last post
  13. BEST LUBRICANT FOR SCREW DRIVE

    Started by Jamesdee‎, 06-12-2016 01:14 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 1,015
    12-08-2016, 04:27 PM Go to last post
  14. Shop Air Dryer

    Started by Dabeechman‎, 12-05-2016 03:33 AM
    air, cnc, running, shop, week
    • Replies: 0
    • Views: 328
    12-05-2016, 03:33 AM Go to last post
  15. Building a dust collection - Help/Ideas/Where To Buy

    Started by Mokra‎, 11-30-2016 06:28 AM
    dust, floor, hose, put, wanting
    • Replies: 0
    • Views: 357
    11-30-2016, 06:28 AM Go to last post
  16. Mikron VCP600-HS

    Started by digicnc‎, 11-25-2016 09:29 AM
    • Replies: 0
    • Views: 181
    11-25-2016, 09:29 AM Go to last post
  17. Question Need Help!- Air pump for oil mist coolant (for DIY CNC router)

    Started by LinuxGuru‎, 09-18-2016 05:46 AM
    • Replies: 1
    • Views: 588
    11-23-2016, 01:22 AM Go to last post
  18. Need Help!- I am looking for a good service Tech in the Vancouver Island area.

    Started by aarong‎, 10-22-2016 01:35 AM
    area, cnc, island, service, vancouver
    • Replies: 0
    • Views: 285
    10-22-2016, 01:35 AM Go to last post

Page 1 of 18 1234 11 ... LastLast

Forum Information and Options

Users Browsing this Forum

There are currently 6 users browsing this forum. (0 members & 6 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands