Maintenance DIY Discussion

Page 1 of 19 123411 ... LastLast
Threads 1 to 20 of 361

Forum: Maintenance DIY Discussion

Discuss anything from how to install a simple light fixture, wiring sub panels, shop air, water, vacuum etc

  1. Question Need Help!- Air pump for oil mist coolant (for DIY CNC router)

    Started by LinuxGuru‎, 09-18-2016 06:46 AM
    • Replies: 3
    • Views: 834
    01-14-2018, 11:43 PM Go to last post
  2. Problem- Rusted Hiwin Linear Bearings

    Started by pagliaso‎, 01-12-2018 10:41 AM
    • Replies: 3
    • Views: 132
    01-13-2018, 11:19 PM Go to last post
  3. Cleaning Linear Glass Scales

    Started by warrenb‎, 01-07-2018 02:01 AM
    cnc, glass, glass scales, heidenhain, scales
    • Replies: 2
    • Views: 192
    01-07-2018, 09:59 PM Go to last post
  4. Need Help!- Harmonic grease 4B-No.2 alternatives?

    Started by Nava‎, 12-25-2017 05:14 PM
    • Replies: 9
    • Views: 317
    12-26-2017, 03:55 PM Go to last post
  5. Pneumatic help

    Started by bobmagnuson‎, 11-12-2017 09:03 PM
    • Replies: 2
    • Views: 378
    11-13-2017, 11:42 AM Go to last post
  6. CNC tool carts

    Started by brian257‎, 10-12-2017 11:23 AM
    cart, cnc, tool, tools, tormach
    • Replies: 0
    • Views: 384
    10-12-2017, 11:23 AM Go to last post
  7. Crappy Limit Switches!

    Started by Barefootboy4‎, 08-05-2017 12:39 AM
    high, limit, replace, steve, wondering
    • Replies: 9
    • Views: 648
    10-08-2017, 06:47 PM Go to last post
  8. Bondo Spoilboard Re-surfacing

    Started by kennected‎, 09-24-2017 11:21 PM
    • Replies: 2
    • Views: 237
    09-25-2017, 08:22 AM Go to last post
  9. Solenoid Cleaning Help

    Started by mgbuck34‎, 09-25-2017 07:42 AM
    cleaning, find, life, push, solenoids
    • Replies: 0
    • Views: 115
    09-25-2017, 07:42 AM Go to last post
  10. Vacuum pump on or off?

    Started by alanhhhhh‎, 09-09-2017 11:35 PM
    completely, hour, run, sheets, vac
    • Replies: 7
    • Views: 416
    09-18-2017, 07:54 PM Go to last post
  11. chips and oil on the wall

    Started by brian257‎, 08-31-2017 01:46 PM
    chips, oil, plastic, stuff, walls
    • Replies: 2
    • Views: 210
    08-31-2017, 02:49 PM Go to last post
  12. Best Dust Collection System for Fab Lab?

    Started by thinktankgroup‎, 07-11-2017 01:30 PM
    • Replies: 0
    • Views: 226
    07-11-2017, 01:30 PM Go to last post
    • Replies: 0
    • Views: 76
    07-11-2017, 12:14 PM Go to last post
  13. Lightbulb Need Help!- Hiding Dust in Fabrication Lab - Paint Advice

    Started by thinktankgroup‎, 07-10-2017 12:04 PM
    fab lab, fabrication lab, kuka, makerspace, paint
    • Replies: 0
    • Views: 146
    07-10-2017, 12:04 PM Go to last post
  14. Step up transformers and amp draw

    Started by rdnck68‎, 06-30-2017 12:07 PM
    machine, panel, transformer, step, amp
    • Replies: 10
    • Views: 401
    07-08-2017, 04:17 PM Go to last post
  15. Vacuum belt?

    Started by Johnauto‎, 04-21-2017 11:44 PM
    belts, issue, normal, vacuum, work
    • Replies: 1
    • Views: 605
    04-22-2017, 07:15 AM Go to last post
  16. Need Help!- HSD ES919 Spindle bearing removal help..

    Started by Stepping3D‎, 10-30-2016 04:09 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 2,244
    04-19-2017, 06:23 AM Go to last post
  17. Hydmech saw vw18

    Started by JKGONZAL‎, 04-17-2017 04:35 PM
    changed, errors, jaws/clamps, move, vw18
    • Replies: 0
    • Views: 141
    04-17-2017, 04:35 PM Go to last post
  18. Newbie- Stones for CNC table upkeep

    Started by RedneckPhysics‎, 03-31-2017 10:26 AM
    cnc, find, high, spots, tormach
    • Replies: 1
    • Views: 306
    04-09-2017, 08:18 PM Go to last post
  19. Problem- Is it possible to disassemble/reuse these Heidenhain connectors?

    Started by BMcCaskill‎, 03-21-2017 12:04 AM
    check, cut, http://imgur.com/1vgaaej, http://imgur.com/iytfsyl, wanted
    • Replies: 5
    • Views: 452
    03-27-2017, 04:39 PM Go to last post

Page 1 of 19 123411 ... LastLast

Forum Information and Options

Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands