Maintenance DIY Discussion

Page 1 of 18 123411 ... LastLast
Threads 1 to 20 of 358

Forum: Maintenance DIY Discussion

Discuss anything from how to install a simple light fixture, wiring sub panels, shop air, water, vacuum etc

  1. Pneumatic help

    Started by bobmagnuson‎, 11-12-2017 09:03 PM
    • Replies: 2
    • Views: 218
    11-13-2017, 11:42 AM Go to last post
  2. CNC tool carts

    Started by brian257‎, 10-12-2017 11:23 AM
    cart, cnc, tool, tools, tormach
    • Replies: 0
    • Views: 371
    10-12-2017, 11:23 AM Go to last post
  3. Crappy Limit Switches!

    Started by Barefootboy4‎, 08-05-2017 12:39 AM
    high, limit, replace, steve, wondering
    • Replies: 9
    • Views: 608
    10-08-2017, 06:47 PM Go to last post
  4. Bondo Spoilboard Re-surfacing

    Started by kennected‎, 09-24-2017 11:21 PM
    • Replies: 2
    • Views: 213
    09-25-2017, 08:22 AM Go to last post
  5. Solenoid Cleaning Help

    Started by mgbuck34‎, 09-25-2017 07:42 AM
    cleaning, find, life, push, solenoids
    • Replies: 0
    • Views: 100
    09-25-2017, 07:42 AM Go to last post
  6. Vacuum pump on or off?

    Started by alanhhhhh‎, 09-09-2017 11:35 PM
    completely, hour, run, sheets, vac
    • Replies: 7
    • Views: 372
    09-18-2017, 07:54 PM Go to last post
  7. chips and oil on the wall

    Started by brian257‎, 08-31-2017 01:46 PM
    chips, oil, plastic, stuff, walls
    • Replies: 2
    • Views: 195
    08-31-2017, 02:49 PM Go to last post
  8. Best Dust Collection System for Fab Lab?

    Started by thinktankgroup‎, 07-11-2017 01:30 PM
    • Replies: 0
    • Views: 197
    07-11-2017, 01:30 PM Go to last post
    • Replies: 0
    • Views: 52
    07-11-2017, 12:14 PM Go to last post
  9. Lightbulb Need Help!- Hiding Dust in Fabrication Lab - Paint Advice

    Started by thinktankgroup‎, 07-10-2017 12:04 PM
    fab lab, fabrication lab, kuka, makerspace, paint
    • Replies: 0
    • Views: 133
    07-10-2017, 12:04 PM Go to last post
  10. Step up transformers and amp draw

    Started by rdnck68‎, 06-30-2017 12:07 PM
    machine, panel, transformer, step, amp
    • Replies: 10
    • Views: 377
    07-08-2017, 04:17 PM Go to last post
  11. Vacuum belt?

    Started by Johnauto‎, 04-21-2017 11:44 PM
    belts, issue, normal, vacuum, work
    • Replies: 1
    • Views: 585
    04-22-2017, 07:15 AM Go to last post
  12. Need Help!- HSD ES919 Spindle bearing removal help..

    Started by Stepping3D‎, 10-30-2016 04:09 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 2,043
    04-19-2017, 06:23 AM Go to last post
  13. Hydmech saw vw18

    Started by JKGONZAL‎, 04-17-2017 04:35 PM
    changed, errors, jaws/clamps, move, vw18
    • Replies: 0
    • Views: 126
    04-17-2017, 04:35 PM Go to last post
  14. Newbie- Stones for CNC table upkeep

    Started by RedneckPhysics‎, 03-31-2017 10:26 AM
    cnc, find, high, spots, tormach
    • Replies: 1
    • Views: 276
    04-09-2017, 08:18 PM Go to last post
  15. Problem- Is it possible to disassemble/reuse these Heidenhain connectors?

    Started by BMcCaskill‎, 03-21-2017 12:04 AM
    check, cut, http://imgur.com/1vgaaej, http://imgur.com/iytfsyl, wanted
    • Replies: 5
    • Views: 423
    03-27-2017, 04:39 PM Go to last post
    • Replies: 2
    • Views: 330
    02-24-2017, 09:09 AM Go to last post
  16. Need Help!- Mazak VTC200b X Axis linear bearing blocks

    Started by kentw‎, 02-09-2017 05:07 PM
    axis, blocks, linear, mazak, vtc200b
    • Replies: 0
    • Views: 334
    02-09-2017, 05:07 PM Go to last post
  17. Question Brother TC-228 Screen not working

    Started by tthayer‎, 12-09-2016 10:52 AM
    brother, brother cnc, cnc, electrical, repair
    • Replies: 2
    • Views: 511
    01-09-2017, 12:39 PM Go to last post
  18. Magnet for hand held Pendant

    Started by Deming‎, 12-10-2016 11:21 PM
    50lb, comments, magnet, pendant, suggestion
    • Replies: 0
    • Views: 239
    12-10-2016, 11:21 PM Go to last post

Page 1 of 18 123411 ... LastLast

Forum Information and Options

Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands