Oh.
No answer...
I must mill some of this parts.
😳
I will create my first 4-axis Code
but the Code dont uses a A-Axis
Here my Settings I use a A-axis in same direction as Axis X
Here you can see other options I think I had correct edited
Now I postprocess the roughing toolpath and get the following result
Here the created code- I cant see a Axis A in my code... WHY??????????????????????????????
O1
G40 G54 G80 G90
(FLAT_END_8)
M06 T8
S22000 F1500 M03
G43 H8
G00 X52.62005 Y40.02979
Z36.98095
G00 Y35.66102 Z32.94492
G01 Y32.72292 Z30.23060 F1500
X6.37995 F1500
X5.58270 Y32.12347 Z30.86682
X5.50080 Y31.91950 Z31.07771
Y31.08090 Z31.91639
X5.58270 Y30.87003 Z32.12039
X6.37995 Y30.23059 Z32.72292
X18.33859
X52.62005
X53.00000 Y31.08090 Z31.91639
Y31.91950 Z31.07771
X52.62005 Y32.72292 Z30.23060
G00 Y40.06817 Z37.01641
G00 X40.83944 Y38.95094 Z38.19028
G00 X29.05883 Y37.79932 Z39.33045
G00 X17.27823 Y36.61435 Z40.43591
G00 X5.49762 Y35.39706 Z41.50568
G00 X0.00000 Y34.81823 Z41.99243
G00 Y30.98853 Z37.37362
G01 Y28.43539 Z34.29442 F1500
Y27.51239 Z35.03921 F1500
Y26.56990 Z35.75917
Y25.60858 Z36.45379
Y24.62911 Z37.12257
Y23.63218 Z37.76505
X0.00200 Y23.12696 Z38.07653
X48.63384
X58.99800
X59.00000 Y23.63218 Z37.76505
Y24.62911 Z37.12257
Y25.60858 Z36.45379
Y26.56990 Z35.75917
Y27.51239 Z35.03921
Y28.43539 Z34.29442
Y29.33822 Z33.52532
Y30.22028 Z32.73245
Y31.08090 Z31.91639
Y31.91950 Z31.07771
Y32.73547 Z30.21700
Y33.52825 Z29.33487
Y34.29726 Z28.43196
Y35.04197 Z27.50889
Y35.76183 Z26.56633
Y36.45635 Z25.60493
Y37.12503 Z24.62539
Y37.76741 Z23.62840
X58.99800 Y38.07653 Z23.12696
X0.00200
X0.00000 Y37.76741 Z23.62840
Y37.12503 Z24.62539
Y36.45635 Z25.60493
Y35.76183 Z26.56633
Y35.04197 Z27.50889
Y34.29726 Z28.43196
G00 Y41.99591 Z34.81403
G00 X0.09969 Y42.88779 Z33.70920
G00 X0.19938 Y43.75062 Z32.58154
G00 X0.29907 Y44.58380 Z31.43179
G00 X0.39876 Y45.38677 Z30.26076
G00 X0.49846 Y46.15900 Z29.06922
G00 X0.59815 Y46.89995 Z27.85798
G00 X0.69784 Y47.60913 Z26.62787
G00 X0.79753 Y48.28605 Z25.37972
G00 X0.89722 Y48.93025 Z24.11438
G00 X0.99691 Y49.54131 Z22.83270
G00 X1.09660 Y50.11879 Z21.53554
G00 X1.19629 Y50.66232 Z20.22379
G00 X1.29598 Y51.17153 Z18.89835
G00 X1.39568 Y51.64606 Z17.56010
G00 X1.49537 Y52.08561 Z16.20995
G00 X1.59506 Y52.48986 Z14.84882
G00 X1.69475 Y52.85855 Z13.47763
G00 X1.79444 Y53.19143 Z12.09730
G00 X1.89413 Y53.48827 Z10.70878
G00 X1.99382 Y53.74887 Z9.31301
G00 X2.09351 Y53.97305 Z7.91092
G00 X2.19320 Y54.16066 Z6.50349
G00 X2.29290 Y54.31158 Z5.09163
G00 X2.39259 Y54.42570 Z3.67633
G00 X2.49228 Y54.50295 Z2.25854
G00 X2.59197 Y54.54327 Z0.83922
G00 X2.69166 Y54.54663 Z-0.58068
G00 X2.79135 Y54.51305 Z-2.00017
G00 X2.89104 Y54.44252 Z-3.41831
G00 X2.99073 Y54.33511 Z-4.83414
G00 X3.09042 Y54.19088 Z-6.24669
G00 X3.19012 Y54.00994 Z-7.65501
G00 X3.28981 Y53.79241 Z-9.05814
G00 X3.38950 Y53.53843 Z-10.45514
G00 X3.48919 Y53.24817 Z-11.84504
G00 X3.58888 Y52.92184 Z-13.22692
G00 X3.68857 Y52.55966 Z-14.59985
G00 X3.78826 Y52.16185 Z-15.96288
G00 X3.88795 Y51.72872 Z-17.31510
G00 X3.98764 Y51.26053 Z-18.65558
G00 X4.08734 Y50.75761 Z-19.98343
G00 X4.18703 Y50.22031 Z-21.29774
G00 X4.28672 Y49.64898 Z-22.59761
G00 X4.38641 Y49.04400 Z-23.88218
G00 X4.48610 Y48.40580 Z-25.15057
G00 X4.58579 Y47.73481 Z-26.40191
G00 X4.68548 Y47.03147 Z-27.63537
G00 X4.78517 Y46.29627 Z-28.85010
G00 X4.88486 Y45.52970 Z-30.04529
G00 X4.98456 Y44.73228 Z-31.22011
G00 X5.08425 Y43.90455 Z-32.37380
G00 X5.18394 Y43.04709 Z-33.50553
G00 X5.28363 Y42.16045 Z-34.61459
G00 X5.38332 Y41.24525 Z-35.70016
G00 X5.48301 Y40.30210 Z-36.76158
G00 X5.58270 Y39.33165 Z-37.79807
G00 Y35.00551 Z-33.64061
G01 Y32.12141 Z-30.86897 F1500
X6.37995 Y32.72292 Z-30.23060 F1500
X52.62005
X53.00000 Y31.91743 Z-31.07983
Y31.07878 Z-31.91846
X52.62005 Y30.23060 Z-32.72292
X6.37995
X5.58270 Y30.86789 Z-32.12244
X5.50080 Y31.07878 Z-31.91846
Y31.91743 Z-31.07983
X5.58270 Y32.12141 Z-30.86897
X5.63052 Y32.29299 Z-30.68944
X5.62868 Y32.44243 Z-30.53140
X5.58080 Y32.57174 Z-30.39343
X5.49050 Y32.68281 Z-30.27396
X5.36138 Y32.77750 Z-30.17139
X5.19708 Y32.85764 Z-30.08411
X5.00121 Y32.92495 Z-30.01044
X4.77737 Y32.98118 Z-29.94863
X4.52920 Y33.02803 Z-29.89695
X3.97431 Y33.10028 Z-29.81694
X2.10164 Y33.26366 Z-29.63456
X1.50454 Y33.34355 Z-29.54465
X1.22735 Y33.39545 Z-29.48597
X0.96923 Y33.45739 Z-29.41567
X0.73379 Y33.53090 Z-29.33184
X0.52465 Y33.61750 Z-29.23255
X0.34542 Y33.71861 Z-29.11587
X0.19972 Y33.83565 Z-28.97977
X0.09118 Y33.96996 Z-28.82221
X0.02340 Y34.12280 Z-28.64110
X0.00000 Y34.29536 Z-28.43424
Y35.04013 Z-27.51123
Y35.76006 Z-26.56872
Y36.45464 Z-25.60736
Y37.12340 Z-24.62786
Y37.76583 Z-23.63092
X0.00200 Y38.07652 Z-23.12697
X58.99800
X59.00000 Y37.76583 Z-23.63092
Y37.12340 Z-24.62786
Y36.45464 Z-25.60736
Y35.76006 Z-26.56872
Y35.04013 Z-27.51123
Y34.29536 Z-28.43424
Y33.52629 Z-29.33711
Y32.73346 Z-30.21918
Y31.91743 Z-31.07983
Y31.07878 Z-31.91846
Y30.21809 Z-32.73447
Y29.33599 Z-33.52727
Y28.43311 Z-34.29631
Y27.51005 Z-35.04105
Y26.56751 Z-35.76095
Y25.60615 Z-36.45550
Y24.62663 Z-37.12422
Y23.62966 Z-37.76662
X58.99800 Y23.12696 Z-38.07653
X0.00200
X0.00000 Y23.62966 Z-37.76662
Y24.62663 Z-37.12422
Y25.60615 Z-36.45550
Y26.56751 Z-35.76095
Y27.51005 Z-35.04105
Y28.43311 Z-34.29631
G00 Y34.81544 Z-41.99474
G00 X0.09969 Y33.71064 Z-42.88666
G00 X0.19938 Y32.58300 Z-43.74953
G00 X0.29907 Y31.43329 Z-44.58274
G00 X0.39876 Y30.26227 Z-45.38577
G00 X0.49846 Y29.07076 Z-46.15803
G00 X0.59815 Y27.85955 Z-46.89902
G00 X0.69784 Y26.62947 Z-47.60824
G00 X0.79753 Y25.38134 Z-48.28520
G00 X0.89722 Y24.11602 Z-48.92945
G00 X0.99691 Y22.83434 Z-49.54055
G00 X1.09660 Y21.53722 Z-50.11807
G00 X1.19629 Y20.22548 Z-50.66165
G00 X1.29598 Y18.90005 Z-51.17090
G00 X1.39568 Y17.56182 Z-51.64548
G00 X1.49537 Y16.21169 Z-52.08507
G00 X1.59506 Y14.85056 Z-52.48937
G00 X1.69475 Y13.47939 Z-52.85810
G00 X1.79444 Y12.09907 Z-53.19102
G00 X1.89413 Y10.71058 Z-53.48791
G00 X1.99382 Y9.31480 Z-53.74856
G00 X2.09351 Y7.91272 Z-53.97279
G00 X2.19320 Y6.50528 Z-54.16045
G00 X2.29290 Y5.09344 Z-54.31142
G00 X2.39259 Y3.67813 Z-54.42558
G00 X2.49228 Y2.26036 Z-54.50288
G00 X2.59197 Y0.84103 Z-54.54324
G00 X2.69166 Y-0.57885 Z-54.54666
G00 X2.79135 Y-1.99835 Z-54.51311
G00 X2.89104 Y-3.41650 Z-54.44263
G00 X2.99073 Y-4.83232 Z-54.33527
G00 X3.09042 Y-6.24488 Z-54.19109
G00 X3.19012 Y-7.65321 Z-54.01019
G00 X3.28981 Y-9.05634 Z-53.79271
G00 X3.38950 Y-10.45335 Z-53.53878
G00 X3.48919 Y-11.84328 Z-53.24856
G00 X3.58888 Y-13.22516 Z-52.92228
G00 X3.68857 Y-14.59811 Z-52.56014
G00 X3.78826 Y-15.96114 Z-52.16239
G00 X3.88795 Y-17.31338 Z-51.72929
G00 X3.98764 Y-18.65388 Z-51.26115
G00 X4.08734 Y-19.98174 Z-50.75828
G00 X4.18703 Y-21.29606 Z-50.22102
G00 X4.28672 Y-22.59597 Z-49.64972
G00 X4.38641 Y-23.88054 Z-49.04480
G00 X4.48610 Y-25.14896 Z-48.40664
G00 X4.58579 Y-26.40032 Z-47.73569
G00 X4.68548 Y-27.63380 Z-47.03239
G00 X4.78517 Y-28.84856 Z-46.29723
G00 X4.88486 Y-30.04377 Z-45.53070
G00 X4.98456 Y-31.21863 Z-44.73332
G00 X5.08425 Y-32.37234 Z-43.90563
G00 X5.18394 Y-33.50410 Z-43.04820
G00 X5.28363 Y-34.61319 Z-42.16160
G00 X5.38332 Y-35.69881 Z-41.24643
G00 X5.48301 Y-36.76023 Z-40.30332
G00 X5.58270 Y-37.79676 Z-39.33291
G00 Y-33.63944 Z-35.00663
G01 Y-30.86790 Z-32.12244 F1500
X6.37995 Y-30.23060 Z-32.72292 F1500
X52.62005
X53.00000 Y-31.07878 Z-31.91846
Y-31.91743 Z-31.07984
X52.62005 Y-32.72292 Z-30.23060
X23.12205
X6.37995
X5.58270 Y-32.12142 Z-30.86896
X5.50080 Y-31.91743 Z-31.07984
Y-31.07878 Z-31.91846
X5.58270 Y-30.86790 Z-32.12244
X5.63052 Y-30.68837 Z-32.29400
X5.62868 Y-30.53032 Z-32.44345
X5.58080 Y-30.39235 Z-32.57275
X5.49050 Y-30.27287 Z-32.68382
X5.36138 Y-30.17030 Z-32.77851
X5.19708 Y-30.08301 Z-32.85864
X5.00121 Y-30.00934 Z-32.92595
X4.77737 Y-29.94754 Z-32.98217
X4.52920 Y-29.89585 Z-33.02902
X3.97431 Y-29.81584 Z-33.10127
X2.10164 Y-29.63345 Z-33.26465
X1.50454 Y-29.54354 Z-33.34453
X1.22735 Y-29.48486 Z-33.39642
X0.96923 Y-29.41456 Z-33.45836
X0.73379 Y-29.33072 Z-33.53188
X0.52465 Y-29.23144 Z-33.61847
X0.34542 Y-29.11475 Z-33.71958
X0.19972 Y-28.97865 Z-33.83661
X0.09118 Y-28.82109 Z-33.97091
X0.02340 Y-28.63997 Z-34.12376
X0.00000 Y-28.43310 Z-34.29631
Y-27.51006 Z-35.04105
Y-26.56752 Z-35.76094
Y-25.60615 Z-36.45549
Y-24.62663 Z-37.12421
Y-23.62965 Z-37.76662
X0.00200 Y-23.12695 Z-38.07653
X58.99800
X59.00000 Y-23.62965 Z-37.76662
Y-24.62663 Z-37.12421
Y-25.60615 Z-36.45549
Y-26.56752 Z-35.76094
Y-27.51006 Z-35.04105
Y-28.43310 Z-34.29631
Y-29.33599 Z-33.52727
Y-30.21809 Z-32.73447
Y-31.07878 Z-31.91846
Y-31.91743 Z-31.07984
Y-32.73346 Z-30.21918
Y-33.52629 Z-29.33711
Y-34.29536 Z-28.43425
Y-35.04013 Z-27.51122
Y-35.76005 Z-26.56872
Y-36.45464 Z-25.60737
Y-37.12339 Z-24.62787
Y-37.76582 Z-23.63093
X58.99800 Y-38.07652 Z-23.12697
X0.00200
X0.00000 Y-37.76582 Z-23.63093
Y-37.12339 Z-24.62787
Y-36.45464 Z-25.60737
Y-35.76005 Z-26.56872
Y-35.04013 Z-27.51122
Y-34.29536 Z-28.43425
G00 Y-41.99358 Z-34.81683
G00 X0.09969 Y-42.88554 Z-33.71207
G00 X0.19938 Y-43.74844 Z-32.58446
G00 X0.29907 Y-44.58170 Z-31.43477
G00 X0.39876 Y-45.38477 Z-30.26377
G00 X0.49846 Y-46.15706 Z-29.07230
G00 X0.59815 Y-46.89810 Z-27.86110
G00 X0.69784 Y-47.60735 Z-26.63106
G00 X0.79753 Y-48.28436 Z-25.38293
G00 X0.89722 Y-48.92865 Z-24.11763
G00 X0.99691 Y-49.53979 Z-22.83599
G00 X1.09660 Y-50.11736 Z-21.53887
G00 X1.19629 Y-50.66098 Z-20.22717
G00 X1.29598 Y-51.17026 Z-18.90178
G00 X1.39568 Y-51.64489 Z-17.56354
G00 X1.49537 Y-52.08453 Z-16.21342
G00 X1.59506 Y-52.48887 Z-14.85232
G00 X1.69475 Y-52.85765 Z-13.48115
G00 X1.79444 Y-53.19062 Z-12.10085
G00 X1.89413 Y-53.48755 Z-10.71235
G00 X1.99382 Y-53.74825 Z-9.31660
G00 X2.09351 Y-53.97252 Z-7.91453
G00 X2.19320 Y-54.16023 Z-6.50710
G00 X2.29290 Y-54.31124 Z-5.09523
G00 X2.39259 Y-54.42546 Z-3.67997
G00 X2.49228 Y-54.50280 Z-2.26218
G00 X2.59197 Y-54.54322 Z-0.84286
G00 X2.69166 Y-54.54668 Z0.57705
G00 X2.79135 Y-54.51318 Z1.99655
G00 X2.89104 Y-54.44275 Z3.41467
G00 X2.99073 Y-54.33543 Z4.83050
G00 X3.09042 Y-54.19130 Z6.24306
G00 X3.19012 Y-54.01045 Z7.65141
G00 X3.28981 Y-53.79301 Z9.05456
G00 X3.38950 Y-53.53913 Z10.45154
G00 X3.48919 Y-53.24897 Z11.84147
G00 X3.58888 Y-52.92272 Z13.22340
G00 X3.68857 Y-52.56063 Z14.59635
G00 X3.78826 Y-52.16292 Z15.95941
G00 X3.88795 Y-51.72987 Z17.31165
G00 X3.98764 Y-51.26178 Z18.65214
G00 X4.08734 Y-50.75895 Z19.98004
G00 X4.18703 Y-50.22173 Z21.29438
G00 X4.28672 Y-49.65048 Z22.59430
G00 X4.38641 Y-49.04560 Z23.87890
G00 X4.48610 Y-48.40749 Z25.14733
G00 X4.58579 Y-47.73658 Z26.39872
G00 X4.68548 Y-47.03332 Z27.63222
G00 X4.78517 Y-46.29820 Z28.84700
G00 X4.88486 Y-45.53171 Z30.04224
G00 X4.98456 Y-44.73436 Z31.21714
G00 X5.08425 Y-43.90673 Z32.37085
G00 X5.18394 Y-43.04933 Z33.50266
G00 X5.28363 Y-42.16277 Z34.61176
G00 X5.38332 Y-41.24763 Z35.69742
G00 X5.48301 Y-40.30455 Z36.75889
G00 X5.58270 Y-39.33419 Z37.79543
G00 Y-35.00777 Z33.63826
G01 Y-32.12349 Z30.86681 F1500
X6.37995 Y-32.72290 Z30.23062 F1500
X52.62005
X53.00000 Y-31.91950 Z31.07771
Y-31.08090 Z31.91639
X52.62005 Y-30.23061 Z32.72290
X6.37995
X5.58270 Y-30.87004 Z32.12039
X5.50080 Y-31.08090 Z31.91639
Y-31.91950 Z31.07771
X5.58270 Y-32.12349 Z30.86681
X5.63052 Y-32.29503 Z30.68729
X5.62868 Y-32.44448 Z30.52922
X5.58080 Y-32.57378 Z30.39123
X5.49049 Y-32.68482 Z30.27179
X5.36138 Y-32.77953 Z30.16919
X5.19707 Y-32.85966 Z30.08190
X5.00120 Y-32.92696 Z30.00823
X4.77736 Y-32.98318 Z29.94643
X4.52919 Y-33.03002 Z29.89476
X3.97429 Y-33.10229 Z29.81471
X2.10163 Y-33.26564 Z29.63234
X1.50453 Y-33.34552 Z29.54242
X1.22735 Y-33.39740 Z29.48375
X0.96923 Y-33.45935 Z29.41344
X0.73379 Y-33.53286 Z29.32960
X0.52464 Y-33.61945 Z29.23030
X0.34542 Y-33.72055 Z29.11362
X0.19972 Y-33.83758 Z28.97751
X0.09118 Y-33.97189 Z28.81995
X0.02340 Y-34.12470 Z28.63884
X0.00000 Y-34.29726 Z28.43196
Y-35.04197 Z27.50888
Y-35.76183 Z26.56633
Y-36.45635 Z25.60493
Y-37.12504 Z24.62539
Y-37.76741 Z23.62839
X0.00200 Y-38.07653 Z23.12695
X38.26968
X58.99800
X59.00000 Y-37.76741 Z23.62839
Y-37.12504 Z24.62539
Y-36.45635 Z25.60493
Y-35.76183 Z26.56633
Y-35.04197 Z27.50888
Y-34.29726 Z28.43196
Y-33.52824 Z29.33488
Y-32.73548 Z30.21699
Y-31.91950 Z31.07771
Y-31.08090 Z31.91639
Y-30.22026 Z32.73246
Y-29.33823 Z33.52531
Y-28.43538 Z34.29442
Y-27.51241 Z35.03920
Y-26.56991 Z35.75917
Y-25.60858 Z36.45379
and so on....
Similar Threads:
Oh.
No answer...
I must mill some of this parts.
😳
Here a Video I made to send it to madCAM Support
Hey, madCam- whats wrong with your Support? There are holidays in sweden?
Its not a free software and a customer can hope of support. I´m totally pissed on!
I must produce my parts and I need a functional G-Code for a AXYZ CNC machine.
All Postprocessors I testet makes waste and in madCam prview I cant see anything - see the screenshot.
Why the PP´s dont write comands for my Y-Axis?
Give me a feedback- i had pay for support!
new findings
If I look the simulation in same direction as the A-Axis I see, that the Y-Axis dont make any movings and is still in the middle of my A-Axis. ...but If I look at the values at the bottom of the window I can see, that the Y-Axis should make moovings to the left and the right.
Whats this???????
figurenholz,
What version of madCAM5 did you purchase 4 Axis/5 Axis/5 Axis Extra?
Is your madCAM file large or private, if not can you post it so I can look at your issues.
The simulation in current madCAM is not fully finished as Joakim has stated in a few posts.
I have 5 Extra but I will try to simulate your issues.
Regards,
Mauri.
figurenholz,
Joakim is very busy trying to finish version 6.
What Controller software are you using?
What Fanuc type does it f support?
At present madCAM5 does not have Planar Roughing that is why roughing movements move everywhere when in a Rotary mode.
However in a finishing cut it does support Planar Finishing.
I have no issues with 4 Axis, however it is important that you use the correct Post Code.
All Post Codes can be further modified to suit your needs and CNC software and machine more precisely (refer the Help Menu).
You can cut along the X Axis or around the A axis depending on how you rotary head is set.
For example I use Mach4 control software and have modified a Post to suit it and my machine.
So it is important that you just do not use any Post process but use one that is closest to your Software and Machine.
Regards,
Mauri.
Your model seems to have a cubic shape. Then I think it will work best with indexed milling. You are using 4-axis with the axis of revolution. If the axis of revolution is the same as your 4th-axis, it will not be any movements in Y.
If you like, you can upload your model here and I will make some sample toolpaths for you.
/Joakim
Hello Joakim and Mauri.
Today I get better results in simulation. I take indexed 4-Axis Mode and rotate the part 4 times in 90degrees steps. I also use clipping planes and the roughing result looks good. (in simulation)
The indexed mode is also the right way to generate the finishing toolpathes?
I had think madcam rotates the A-axis independently and also moves the XYZ axes to work all sites in a rollover.
;o(((
Whats the advantage of 4-axis in contrast to tighten my material on a table and rotate it manually when the Cam dont work with all the axis? In revolving mode it dont use Y and in indexing mode it dont use A.
Other machines I see work in rollover the A-axis and do cuttings behind on all sides.
I´m totally sad.
I cant upload my file. The .zip is 10MB and the max size is 8.5
Figurenholz, you need to discover the cloud. Set up a OneDrive account and you can just send a link to Joakim, and he can download the file. File size doesn't matter.
Also, if you want to make screen captures, whether still shots or video, look at a product called Jing.
https://www.techsmith.com/jing-tool.html
These Techsmith tools are great, and Jing is free. Set up a ScreenCast account (free again) and you can share the videos.
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Hello.
Thank you for the link
last week I search for a screen recorder and havent found a free version ;o)
Thank you
Okay, I activate OneDrive
Here is the link
https://1drv.ms/u/s!AsRGBxXm2wWHhgAT0KG5edRiVztR
Take a look at SnagIt too. There is a minimal cost but it's worth every cent. There is not a day that goes by that I don't use it.
https://www.techsmith.com/screen-capture.html
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Hello again.
Many thanks to Joakim from sweden. He shows me in a video what I must do to create the passes. The way I go to my passes was nearly the same but the mistake between madCam and my machine comes later ;o)
I create a file, then I postprocess it and in the postprocess window I edit the home postion. Here I can write 0,0,0 or 100,100,100
The result in machine prview is still the same. The Flat end stand in a undefined postion into my stock ;o(
Why its so?
Also the 2 Test-toolpasses that comes from the right and left side of my material are in machining preview in mysterious positions and the rotation is in X0, Y0 Axle...
I cant exlain it better because my english is bad.
please see the video below.