Only getting 48 lines of code?

[Crawler374]

I have the Mach3 free download. I have drawn a design in cambam and when I transfer it over to mach3, I am only getting 48 lines of code. I think I should have around 300 lines if the project is done. anyone have some ideas of pointers?

[ger21]

Is there an error message displayed? Mach3 will run 500 lines of code, then just stop if there is more. If there's no error, can you post the code?

[Crawler374]

No, there is no error.

Here is the code that mach sees.

N5 (File Name = WWWW on Sunday, September 20, 2009)
N10 (Default Mill Post)
N15 G91.1
N20 G0 Z1.0000
N25 M3
N30 X3.7925 Y4.0471
N35 Z0.1000
N40 G1 Z0.0000 F60.00
N45 X5.0606 Y4.0391
N50 G0 Z1.0000
N55 X5.1777 Y4.0409
N60 Z0.1000
N65 G1 Z0.0000
N70 G2 X5.0606 Y4.0390 I-0.0782 J1.2210
N75 G0 Z1.0000
N80 X5.1777 Y4.0410
N85 Z0.1000
N90 G1 Z0.0000
N95 G3 X5.2290 Y4.0520 I-0.0141 J0.1912
N100 X5.2633 Y4.0713 I-0.0498 J0.1284
N105 X5.3746 Y4.2001 I-0.4993 J0.5439
N110 G0 Z1.0000
N115 X6.3813 Y5.5158
N120 Z0.1000
N125 G1 Z0.0000
N130 X5.3746 Y4.2001
N135 G0 Z1.0000
N140 X6.3813 Y5.5158
N145 Z0.1000
N150 G1 Z0.0000
N155 G2 X6.5010 Y5.6632 I2.0652 J-1.5554
N160 X6.5643 Y5.7181 I0.2330 J-0.2045
N165 G0 Z1.0000
N170 X6.5644 Y5.7180
N175 Z0.1000
N180 G1 Z0.0000
N185 G2 X6.6128 Y5.7391 I0.0978 J-0.1583
N190 X6.8040 Y5.7525 I0.1504 J-0.7820
N195 G0 Z1.0000
N200 X9.4278 Y5.7432
N205 Z0.1000
N210 G1 Z0.0000
N215 G3 X9.1920 Y5.7528 I-0.1782 J-1.4835
N220 G1 X9.1814 Y5.7528
N225 X6.8040 Y5.7525
N230 G0 Z1.0000
N235 X9.5487 Y5.7077
N240 Z0.1000
N245 G1 Z0.0000
N250 G3 X9.4279 Y5.7432 I-0.4745 J-1.3934

[Crawler374]

i think i got it figured out, i think i missed a step in the tool path. I will reply with updates later.

[Crawler374]

I missed a step in CamBam, thanks Gerry.