Laser Hardware

Page 1 of 6 1234 ... LastLast
Threads 1 to 20 of 109

Forum: Laser Hardware

Sub-Forums Threads / Posts  Last Post

  1. Laser CO2 Tubes, Diodes, RF and Power Supplies here.

    Forum Actions:

    Forum Statistics:

    • Threads: 112
    • Posts: 656
  2. Laser Optics

    (2 Viewing)

    Discuss mirrors, beam expanders and other Optics here.

    Forum Actions:

    Forum Statistics:

    • Threads: 30
    • Posts: 110

    Last Post:

  3. Discuss chillers and other cooling methods.

    Forum Actions:

    Forum Statistics:

    • Threads: 12
    • Posts: 69
  1. Issue with microstep driver (Z axis)

    Started by ZedWings‎, 03-22-2017 06:05 PM
    • Replies: 7
    • Views: 166
    03-23-2017, 12:58 PM Go to last post
  2. Question: 15W Blue Laser Module PWM settings

    Started by rjsavell‎, 03-19-2017 05:54 PM
    15w, laser, led, pwm laser controller
    • Replies: 4
    • Views: 174
    03-22-2017, 08:10 PM Go to last post
  3. Chinese 40W K40 problem- PSU or Laser tube??!!

    Started by spartagates‎, 03-19-2017 05:18 PM
    button, power, purple, supply, tube
    • Replies: 0
    • Views: 71
    03-19-2017, 05:18 PM Go to last post
  4. Chinese laser Fault, advice please

    Started by Eagl-s‎, 03-04-2017 12:57 PM
    fault, hours, laser, part, power
    • Replies: 1
    • Views: 190
    03-04-2017, 07:22 PM Go to last post
  5. power supply adaptation for 90W Reci tube

    Started by keverett‎, 02-24-2017 10:46 PM
    laser, laser power supply, mismatched laser supply, power, supply
    • Replies: 0
    • Views: 117
    02-24-2017, 10:46 PM Go to last post
    • Replies: 0
    • Views: 154
    02-23-2017, 07:50 AM Go to last post
  6. Laser Calorimetry

    Started by The Geekineer‎, 02-18-2017 08:46 PM
    calorimetry, laser, laser power, measure, power measurement
    • Replies: 4
    • Views: 164
    02-19-2017, 11:03 PM Go to last post
  7. Post NEED HELP! Chinese 60w Laser cutter won´t turn on.

    Started by arqmoe‎, 07-08-2016 09:10 AM
    • Replies: 5
    • Views: 515
    02-18-2017, 02:58 PM Go to last post
  8. Laser not firing from controller.

    Started by EricC‎, 02-11-2017 06:39 PM
    • Replies: 0
    • Views: 134
    02-11-2017, 06:39 PM Go to last post
  9. Full Spectrum Laser stepper motor identification

    Started by dynamicCNC‎, 12-02-2015 04:57 PM
    full, hobby, laser, motor, stepper
    • Replies: 1
    • Views: 475
    02-09-2017, 06:04 PM Go to last post
    • Replies: 3
    • Views: 172
    02-08-2017, 07:17 AM Go to last post
  10. what laser to buy to cut 3 mm mdf ? help

    Started by ISAIAS‎, 10-28-2016 07:56 AM
    2 Pages
    1 2
    • Replies: 23
    • Views: 1,314
    01-20-2017, 10:50 PM Go to last post
    • Replies: 1
    • Views: 359
    01-12-2017, 01:12 AM Go to last post
  11. Posted in wrong section Advice for Newb

    Started by Stoksey‎, 06-16-2016 04:40 AM
    beginning, engineer, mark, power, settings
    • Replies: 4
    • Views: 493
    01-05-2017, 02:41 PM Go to last post
  12. Laser controller unit

    Started by actionscripter‎, 11-24-2016 11:35 PM
    awc708c, board, control, cutter, laser
    • Replies: 0
    • Views: 279
    11-24-2016, 11:35 PM Go to last post
  13. X and Y Axis reversed - need help

    Started by designwerx1967‎, 11-22-2016 04:00 PM
    #rdc644xg, axis, hitting, mirrored, side
    • Replies: 0
    • Views: 180
    11-22-2016, 04:00 PM Go to last post
  14. Poll Poll: Upgrading laser cutter control card Leetro MPC6515 ?

    Started by Paul Shroom‎, 05-16-2014 10:59 PM
    • Replies: 2
    • Views: 3,531
    11-20-2016, 09:07 PM Go to last post
    • Replies: 1
    • Views: 733
    11-18-2016, 06:11 PM Go to last post
  15. Printed circuit Board etch?

    Started by Ralphxyz‎, 11-13-2016 06:54 PM
    etch, laser, meter, problems, size
    • Replies: 7
    • Views: 454
    11-14-2016, 05:06 PM Go to last post
  16. laser cutting head / acryl glas up to 10mm

    Started by fhartmann‎, 11-13-2016 04:24 AM
    • Replies: 0
    • Views: 234
    11-13-2016, 04:24 AM Go to last post

Page 1 of 6 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 10 users browsing this forum. (0 members & 10 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands