Laser Hardware

Page 1 of 6 1234 ... LastLast
Threads 1 to 20 of 103

Forum: Laser Hardware

Sub-Forums Threads / Posts  Last Post

  1. Laser CO2 Tubes, Diodes, RF and Power Supplies here.

    Forum Actions:

    Forum Statistics:

    • Threads: 112
    • Posts: 643
  2. Laser Optics

    (2 Viewing)

    Discuss mirrors, beam expanders and other Optics here.

    Forum Actions:

    Forum Statistics:

    • Threads: 30
    • Posts: 110

    Last Post:

  3. Laser Cooling

    (3 Viewing)

    Discuss chillers and other cooling methods.

    Forum Actions:

    Forum Statistics:

    • Threads: 12
    • Posts: 69
  1. Laser Calorimetry

    Started by The Geekineer‎, 02-18-2017 09:46 PM
    calorimetry, laser, laser power, measure, power measurement
    • Replies: 4
    • Views: 118
    02-20-2017, 12:03 AM Go to last post
  2. Post NEED HELP! Chinese 60w Laser cutter won´t turn on.

    Started by arqmoe‎, 07-08-2016 10:10 AM
    • Replies: 5
    • Views: 475
    02-18-2017, 03:58 PM Go to last post
  3. Laser not firing from controller.

    Started by EricC‎, 02-11-2017 07:39 PM
    • Replies: 0
    • Views: 101
    02-11-2017, 07:39 PM Go to last post
  4. Full Spectrum Laser stepper motor identification

    Started by dynamicCNC‎, 12-02-2015 05:57 PM
    full, hobby, laser, motor, stepper
    • Replies: 1
    • Views: 450
    02-09-2017, 07:04 PM Go to last post
    • Replies: 3
    • Views: 125
    02-08-2017, 08:17 AM Go to last post
  5. what laser to buy to cut 3 mm mdf ? help

    Started by ISAIAS‎, 10-28-2016 08:56 AM
    2 Pages
    1 2
    • Replies: 23
    • Views: 1,208
    01-20-2017, 11:50 PM Go to last post
    • Replies: 1
    • Views: 343
    01-12-2017, 02:12 AM Go to last post
  6. Posted in wrong section Advice for Newb

    Started by Stoksey‎, 06-16-2016 05:40 AM
    beginning, engineer, mark, power, settings
    • Replies: 4
    • Views: 461
    01-05-2017, 03:41 PM Go to last post
  7. Laser controller unit

    Started by actionscripter‎, 11-25-2016 12:35 AM
    awc708c, board, control, cutter, laser
    • Replies: 0
    • Views: 232
    11-25-2016, 12:35 AM Go to last post
  8. X and Y Axis reversed - need help

    Started by designwerx1967‎, 11-22-2016 05:00 PM
    #rdc644xg, axis, hitting, mirrored, side
    • Replies: 0
    • Views: 155
    11-22-2016, 05:00 PM Go to last post
  9. Poll Poll: Upgrading laser cutter control card Leetro MPC6515 ?

    Started by Paul Shroom‎, 05-16-2014 11:59 PM
    • Replies: 2
    • Views: 3,452
    11-20-2016, 10:07 PM Go to last post
    • Replies: 1
    • Views: 704
    11-18-2016, 07:11 PM Go to last post
  10. Printed circuit Board etch?

    Started by Ralphxyz‎, 11-13-2016 07:54 PM
    etch, laser, meter, problems, size
    • Replies: 7
    • Views: 391
    11-14-2016, 06:06 PM Go to last post
  11. laser cutting head / acryl glas up to 10mm

    Started by fhartmann‎, 11-13-2016 05:24 AM
    • Replies: 0
    • Views: 211
    11-13-2016, 05:24 AM Go to last post
  12. I want to upgrade my K40 laser cutter controller!

    Started by slow_rider‎, 05-25-2016 08:44 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 2,662
    10-28-2016, 06:35 AM Go to last post
  13. Universal Laser ULS 25, Rebuilt Laser or Power Supply

    Started by Trell‎, 09-25-2016 09:22 AM
    25 watts, laser, universal, universal laser uls 25
    • Replies: 0
    • Views: 239
    09-25-2016, 09:22 AM Go to last post
  14. Odd Unfocused beam

    Started by billturnbull‎, 07-19-2016 10:37 PM
    • Replies: 7
    • Views: 518
    09-14-2016, 02:36 AM Go to last post
  15. New power supply only goes to 11mA with 50W laser

    Started by CO2-Lucy‎, 09-09-2016 08:49 AM
    • Replies: 4
    • Views: 400
    09-12-2016, 07:22 AM Go to last post
    • Replies: 3
    • Views: 331
    09-10-2016, 10:13 AM Go to last post
  16. Laser Tube CO2 PSU

    Started by baron_africa‎, 09-01-2016 11:01 AM
    • Replies: 4
    • Views: 315
    09-02-2016, 05:20 PM Go to last post

Page 1 of 6 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 17 users browsing this forum. (0 members & 17 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands