Laser Hardware

Page 1 of 6 1234 ... LastLast
Threads 1 to 20 of 110

Forum: Laser Hardware

Sub-Forums Threads / Posts  Last Post

  1. Laser CO2 Tubes, Diodes, RF and Power Supplies here.

    Forum Actions:

    Forum Statistics:

    • Threads: 112
    • Posts: 657

    Last Post:

  2. Laser Optics

    (3 Viewing)

    Discuss mirrors, beam expanders and other Optics here.

    Forum Actions:

    Forum Statistics:

    • Threads: 30
    • Posts: 110

    Last Post:

  3. Laser Cooling

    (2 Viewing)

    Discuss chillers and other cooling methods.

    Forum Actions:

    Forum Statistics:

    • Threads: 12
    • Posts: 69
  1. Banggood 7w Laser Mounted to CNC Machine

    Started by denmark219‎, 04-18-2017 11:03 AM
    • Replies: 0
    • Views: 102
    04-18-2017, 11:03 AM Go to last post
  2. Question: 15W Blue Laser Module PWM settings

    Started by rjsavell‎, 03-19-2017 05:54 PM
    15w, laser, led, pwm laser controller
    • Replies: 5
    • Views: 382
    03-28-2017, 11:48 AM Go to last post
  3. Issue with microstep driver (Z axis)

    Started by ZedWings‎, 03-22-2017 06:05 PM
    • Replies: 7
    • Views: 197
    03-23-2017, 12:58 PM Go to last post
  4. Chinese 40W K40 problem- PSU or Laser tube??!!

    Started by spartagates‎, 03-19-2017 05:18 PM
    button, power, purple, supply, tube
    • Replies: 0
    • Views: 121
    03-19-2017, 05:18 PM Go to last post
  5. Chinese laser Fault, advice please

    Started by Eagl-s‎, 03-04-2017 12:57 PM
    fault, hours, laser, part, power
    • Replies: 1
    • Views: 232
    03-04-2017, 07:22 PM Go to last post
  6. power supply adaptation for 90W Reci tube

    Started by keverett‎, 02-24-2017 10:46 PM
    laser, laser power supply, mismatched laser supply, power, supply
    • Replies: 0
    • Views: 126
    02-24-2017, 10:46 PM Go to last post
    • Replies: 0
    • Views: 210
    02-23-2017, 07:50 AM Go to last post
  7. Laser Calorimetry

    Started by The Geekineer‎, 02-18-2017 08:46 PM
    calorimetry, laser, laser power, measure, power measurement
    • Replies: 4
    • Views: 187
    02-19-2017, 11:03 PM Go to last post
  8. Post NEED HELP! Chinese 60w Laser cutter won´t turn on.

    Started by arqmoe‎, 07-08-2016 09:10 AM
    • Replies: 5
    • Views: 545
    02-18-2017, 02:58 PM Go to last post
  9. Laser not firing from controller.

    Started by EricC‎, 02-11-2017 06:39 PM
    • Replies: 0
    • Views: 144
    02-11-2017, 06:39 PM Go to last post
  10. Full Spectrum Laser stepper motor identification

    Started by dynamicCNC‎, 12-02-2015 04:57 PM
    full, hobby, laser, motor, stepper
    • Replies: 1
    • Views: 488
    02-09-2017, 06:04 PM Go to last post
    • Replies: 3
    • Views: 206
    02-08-2017, 07:17 AM Go to last post
  11. what laser to buy to cut 3 mm mdf ? help

    Started by ISAIAS‎, 10-28-2016 07:56 AM
    2 Pages
    1 2
    • Replies: 23
    • Views: 1,424
    01-20-2017, 10:50 PM Go to last post
    • Replies: 1
    • Views: 367
    01-12-2017, 01:12 AM Go to last post
  12. Posted in wrong section Advice for Newb

    Started by Stoksey‎, 06-16-2016 04:40 AM
    beginning, engineer, mark, power, settings
    • Replies: 4
    • Views: 514
    01-05-2017, 02:41 PM Go to last post
  13. Laser controller unit

    Started by actionscripter‎, 11-24-2016 11:35 PM
    awc708c, board, control, cutter, laser
    • Replies: 0
    • Views: 302
    11-24-2016, 11:35 PM Go to last post
  14. X and Y Axis reversed - need help

    Started by designwerx1967‎, 11-22-2016 04:00 PM
    #rdc644xg, axis, hitting, mirrored, side
    • Replies: 0
    • Views: 188
    11-22-2016, 04:00 PM Go to last post
  15. Poll Poll: Upgrading laser cutter control card Leetro MPC6515 ?

    Started by Paul Shroom‎, 05-16-2014 10:59 PM
    • Replies: 2
    • Views: 3,603
    11-20-2016, 09:07 PM Go to last post
    • Replies: 1
    • Views: 744
    11-18-2016, 06:11 PM Go to last post
  16. Printed circuit Board etch?

    Started by Ralphxyz‎, 11-13-2016 06:54 PM
    etch, laser, meter, problems, size
    • Replies: 7
    • Views: 503
    11-14-2016, 05:06 PM Go to last post

Page 1 of 6 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 14 users browsing this forum. (0 members & 14 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands