Larken Router Models - CNCzone.com-The Largest Machinist Community on the net!

routerman · #1 04-14-2003, 06:19 PM

I have a 2424 Camtool router from larken which works great. I see Larken has added to new models to its line, a small 15x15 and a 50x50.

balsaman · #2 04-15-2003, 12:23 AM

Hi, welcome to CNCzone, Where in Canada are ya? I am in Ontario near Woodstock.

Eric

MikeBerry · #3 06-01-2003, 08:07 PM

What's the real deal with Larken? I have attempted to contact Larry there, but just get the runaround. Have sent him e mails but stll no response. I guess I am thinking twice about a Larken router.......

Any suggestions to get this guy to wake up?

Thanks,
Mike

routerman · #4 07-07-2003, 12:54 AM

Larken Automation moved to a new location at in the 1st weeks of june.
The new phone# is 613-746-5970

danchiru · #5 07-25-2003, 01:35 PM

Guys:

This is SHOPCAM!!!!!!
Why are you posting comments (good or bad) about Larken ?

routerman · #6 08-28-2003, 10:47 PM

This is SHOPCAM!! Why are you posting comments about Larken ?

You are in the wrong forum, Dan, look before you click.

Budcan2 · #7 09-22-2003, 07:52 PM

Talked to Larry a couple of days ago. StarCam will not be available
to the general public until approx. the end of November. We use
LCam software on both our homebuilt tables in our sign shop
with great results. If StarCam is as user friendly and efficient
as their DOS based software, it's going to be a winner!

DLMACHINE · #8 02-11-2004, 02:55 AM

I got my hands on Starcam today and I have to say "I like it".

routerman · #9 03-06-2004, 11:12 PM

You can download the new StarCam at larkens website www.LarkenCNC.com
It consists of 2 programs, the StarCam graphical Importing, editing and Layout frontend, and the StarCNC spooler that sends to the processor in the control box.
Check it out.

Al_The_Man · #10 03-07-2004, 11:21 AM

I have installed a Larken 4'x8' table using the older DOS ver, Larry was talking about using servo's on the later WIN ver, Is he doing that?
I know from experience Larry can be frustratingly elusive sometime's.
Al

Al_The_Man · #11 03-12-2004, 03:19 PM

You Guy's that are running Starcam, are you running it on an older Lcam machine or just in simulation? Larry mentioned that it will need a hardware upgrade before I run it on the older dos version.
Al

DLMACHINE · #12 03-14-2004, 12:19 PM

The older version does require a hardware upgrade to the controller box itself.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Finding The Right Router	Crushmonkey	Commercial CNC Wood Routers	22	06-19-2006 02:17 AM
long term stability of wood framed router	dave925	DIY-CNC Router Table Machines	17	05-06-2005 12:33 AM
buscht's cnc router	buscht	DIY-CNC Router Table Machines	25	04-13-2004 12:43 PM
My first CNC router: 1.5 years building	hddjohns	DIY-CNC Router Table Machines	2	04-03-2004 11:18 AM
Larken	CNC Pro	Larken	1	02-11-2004 08:14 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)