Trouble Setting parameters Yasnac I80


Results 1 to 6 of 6

Thread: Trouble Setting parameters Yasnac I80

  1. #1
    Registered
    Join Date
    Dec 2009
    Location
    USA
    Posts
    7
    Downloads
    0
    Uploads
    0

    Unhappy Trouble Setting parameters Yasnac I80

    I'm hoping someone out there can help. I have a motion problem with my machine and am trying to set parameters so I can see the actual spindle RPM to determine the problem, I'm also trying to turn off the spindle speed check bit to get around the ppoblem. Using the book as a reference I am turning on the parameter set mode. I then change the parameters and as the manual instructs I am turning off the power. After powering up I turn off the parameter change bit and the parameters appear to have been changed but do not actually change any function of the machine. Our service guy ran into the same problem trying to adjust for backlash. Kitamura has not been able to help and Yaskawa who now takes care of Yasnac service has not been able to help. Any input would be appreciated.

    Art

    Similar Threads:


  2. #2
    Registered
    Join Date
    Mar 2006
    Location
    USA
    Posts
    27
    Downloads
    0
    Uploads
    0

    Default FC200 Switch

    I know this is well over a year ago, but did you use the FC200 board's rotating switch (position 2) to allow for parameter setting? Once set, power down, rotate switch back to Zero (0) and reboot.



  3. #3
    Banned yours_prabhat's Avatar
    Join Date
    Dec 2008
    Location
    India
    Posts
    239
    Downloads
    0
    Uploads
    0

    Default

    please give the drive number if possible the PCB number also



  4. #4
    Registered
    Join Date
    Dec 2009
    Location
    USA
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default

    If anybody else has this problem let me explain what we found out.

    Apparently these Yasnac Controls can get themselves into a state where the parameters change but they just don't register. We figured this out when we had the processor board replaced six months ago. I was down for 3 weeks. Yaskawa actually had the main chassis at thier facility and gave it a good to go and it still wouldn't work in my machine. I got a copy of the original parameters from Kitamura and input them by hand and still no luck. The errors varied but the machine never started. So that I would not need to manually input the parameters again we backed up the parameters and did yet another memory wipe. We then loaded the parameters via the serial port and the machine started right up. It also now takes parameter updates through the keypad. Don't ask me why, I don't know and Yaskawa can't explain it. So if you are one of the many shops that can't adjust backlash or other critical parameters, just try backing up the system parameters, do a memory wipe and reload the parameters using the serial port and you will probably be able to manually change parameters.



  5. #5
    Registered
    Join Date
    Aug 2009
    Location
    India
    Posts
    9
    Downloads
    0
    Uploads
    0

    Default Re: Trouble Setting parameters Yasnac I80

    Hi,
    I am Srikrish R from Tamilnadu, India. I have one used very old VMC machine with YASNAC i80M control. In that machine I lost all the parameters due to bad battery. I am unable to run the machine for the last 4 years. kindly send me the Option parameters from opm00. Please do the needful immediately. My email ID is : rsrikrish1984@gmail.com.

    - - - Updated - - -

    Hi,
    I am Srikrish R from Tamilnadu, India. I have one used very old VMC machine with YASNAC i80M control. In that machine I lost all the parameters due to bad battery. I am unable to run the machine for the last 4 years. kindly send me the Option parameters from opm00. Please do the needful immediately. My email ID is : rsrikrish1984@gmail.com.



  6. #6
    Registered
    Join Date
    Aug 2009
    Location
    India
    Posts
    9
    Downloads
    0
    Uploads
    0

    Default Re: Trouble Setting parameters Yasnac I80

    Hi,
    I am Srikrish R from Tamilnadu, India. I have one used very old VMC machine with YASNAC i80M control. In that machine I lost all the parameters due to bad battery. I am unable to run the machine for the last 4 years. kindly send me the Option parameters from opm00. Please do the needful immediately. My email ID is : rsrikrish1984@gmail.com.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Trouble Setting parameters Yasnac I80
Trouble Setting parameters Yasnac I80