Results 1 to 5 of 5

Thread: Delrin Guides??

  1. #1
    Registered cuecaps's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    Delrin Guides??

    My K2 is a Great Machine, but, as seen earlier,
    theres no end bearings for the Lead Screw.
    Those Guide Rods are so big, they must keep the alignment.
    maybe that's why K-2 didn't put them. Short Travel.
    I just wanted to have something there to keep alignment for the Lead Screws
    So.....
    Attached Thumbnails Attached Thumbnails Delrin Guides??-delrin_guide_1.jpg  
    Last edited by cuecaps; 02-01-2009 at 05:28 PM.


  2. #2
    Registered cuecaps's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    Delrin Guide

    I made this Delrin Guide.
    It fits in the End Plates.
    And....
    Attached Thumbnails Attached Thumbnails Delrin Guides??-delrin_guide.jpg  


  3. #3
    Registered cuecaps's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    Delrin Guides

    Here it is on my K2 Mill.
    It has a close fit to the Lead Screw, so, it spinds with it.
    The Outside Diameter fits into the space in the Guide Plates,so, it doesn't hinder the travel.
    Attached Thumbnails Attached Thumbnails Delrin Guides??-delrin_guide_2.jpg  


  4. #4
    Registered cuecaps's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    My K2 CNC MILL

    Here's my K2 Mill.
    Clear Plexi back Panels.
    Aluminum add ons..
    Attached Thumbnails Attached Thumbnails Delrin Guides??-k2_cnc_6.jpg  
    Last edited by cuecaps; 02-01-2009 at 05:20 PM. Reason: Photo


  • #5
    Registered cuecaps's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    KTM 7040

    Close-up.....

    I don't know enough to give a review...
    Still learning to run it...
    Joey told me about K2's CNC Mill.
    Thanks for tht lead to K2 Joey.
    Hey Tauseef,
    I got one of their Bosh Colt Router Mounts too.
    Just in case I wanted to go with a Trimmer later.
    The Makita 1101 is great, but, it's an overkill...
    I put on a air deflector at the bottom because the Makita
    blows air down thru the Body and out where the spindle and dust is.

    Thanks for viewing..
    Attached Thumbnails Attached Thumbnails Delrin Guides??-k2_cnc_5a.jpg  
    Last edited by cuecaps; 02-01-2009 at 07:59 PM. Reason: Add info


  • Similar Threads

    1. Delrin Slider Guides
      By signsdesigns in forum Want To Buy...Need help!
      Replies: 0
      Last Post: 08-05-2008, 12:01 PM
    2. Any C6 setup guides out there?
      By MadMax in forum Syil Products
      Replies: 8
      Last Post: 03-08-2008, 09:37 PM
    3. Linear guides help !!!
      By zeoncomp in forum General Waterjet
      Replies: 2
      Last Post: 09-04-2007, 02:04 PM
    4. Linear guides
      By canadamaxxer in forum General Waterjet
      Replies: 0
      Last Post: 11-30-2006, 01:32 PM
    5. guides and slides
      By bean7795 in forum DIY CNC Router Table Machines
      Replies: 2
      Last Post: 04-11-2004, 09:24 PM

    Posting Permissions



    About CNCzone.com

      We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

    Follow us on

    Facebook Dribbble RSS Feed


    Search Engine Friendly URLs by vBSEO ©2011, Crawlability, Inc.