Hypertherm Plasma


Page 1 of 30 123411 ... LastLast
Threads 1 to 20 of 599

Forum: Hypertherm Plasma

Discuss hypertherm plasma machines here.

    • Replies: 1
    • Views: 152
    01-21-2018, 01:57 PM Go to last post
  1. Hypertherm 30xp J12 connector

    Started by 840evo‎, 12-27-2017 01:31 PM
    connector, j12, pcb, start, torch
    • Replies: 2
    • Views: 169
    01-10-2018, 08:01 AM Go to last post
  2. Hypertherm 45 torch cap sensor fault

    Started by Danno‎, 12-31-2017 03:59 PM
    consumables, hypertherm, micro, single, switch
    • Replies: 4
    • Views: 226
    01-07-2018, 11:40 AM Go to last post
  3. Unhappy Need Help!- Postprocessor Pronest for ZINSER CNC2010

    Started by toilaai202‎, 01-05-2018 05:09 PM
    cnc2010, machine, postprocessor, pronest, zinser
    • Replies: 0
    • Views: 113
    01-05-2018, 05:09 PM Go to last post
  4. Help locating correct Powermax45 trigger wires for remote CNC start

    Started by jerryrigge‎, 02-10-2010 11:13 PM
    2 Pages
    1 2
    not, onto
    • Replies: 17
    • Views: 9,754
    01-02-2018, 02:31 AM Go to last post
  5. HyAmp Machine torch and 65A machine

    Started by paulmacc‎, 12-21-2017 10:47 AM
    cnc, hyamp, machine, mod, torch
    • Replies: 2
    • Views: 162
    12-22-2017, 05:33 AM Go to last post
  6. Need Help!- Connecting PowerMax 65 to Chinese THC and Controller

    Started by kamkama‎, 12-17-2017 05:29 PM
    • Replies: 0
    • Views: 152
    12-17-2017, 05:29 PM Go to last post
  7. Powermax 30XP + Plasmacam

    Started by phuffman‎, 11-15-2017 12:19 AM
    30xp, airlines/compressor, plasmacam, powermax, system
    • Replies: 1
    • Views: 409
    11-15-2017, 12:11 PM Go to last post
  8. Plasma tip dragging on steel

    Started by mrobs‎, 11-10-2017 09:13 AM
    cut, drags, part, plasma, tip
    • Replies: 2
    • Views: 186
    11-10-2017, 11:25 AM Go to last post
  9. Burning Countersunk Holes

    Started by Stovtop‎, 11-08-2017 11:04 AM
    counter, holes, square, sunk, wondering
    • Replies: 0
    • Views: 139
    11-08-2017, 11:04 AM Go to last post
  10. Grey electrodes, Hypertherm Powermax 105

    Started by Fyresparxx‎, 10-06-2017 11:07 AM
    • Replies: 2
    • Views: 470
    10-06-2017, 12:06 PM Go to last post
  11. CPC PORT VOLTAGE DIVIDER SOURCE CURRENT

    Started by cristobalmunoz‎, 09-30-2017 05:58 PM
    cpc, divider, specifications, voltage
    • Replies: 1
    • Views: 281
    10-01-2017, 09:41 AM Go to last post
  12. Need Help!- HYPERTHERM MAX200 TORCH HARD ARC STATING

    Started by yahya990‎, 09-21-2017 10:45 PM
    • Replies: 2
    • Views: 215
    09-27-2017, 09:49 AM Go to last post
    • Replies: 6
    • Views: 3,257
    09-23-2017, 04:12 PM Go to last post
  13. Need Help!- Bad Dross Fine Cut Powermax 105

    Started by Fyresparxx‎, 09-08-2017 07:16 PM
    • Replies: 8
    • Views: 402
    09-19-2017, 10:09 AM Go to last post
    • Replies: 1
    • Views: 258
    09-19-2017, 07:57 AM Go to last post
  14. Are these original hypertherm spare partes?

    Started by mzerighi‎, 08-24-2017 06:13 AM
    • Replies: 7
    • Views: 383
    09-17-2017, 08:08 AM Go to last post
  15. Need Help!- Hypertherm MAX42 torch retrofit

    Started by pmdgoncal‎, 09-08-2017 06:23 PM
    comments, max, max42, pedro, torch
    • Replies: 1
    • Views: 193
    09-11-2017, 06:38 PM Go to last post
  16. Help with torch installation

    Started by Spitterkat‎, 09-07-2017 06:03 PM
    height, installed, pierce, set, torch
    • Replies: 0
    • Views: 152
    09-07-2017, 06:03 PM Go to last post
  17. Red face Need Help!- Hypertherm Sensor Torch Height Control

    Started by francis_liang‎, 02-16-2017 01:52 AM
    arc, problem, sensor, thc, torch
    • Replies: 4
    • Views: 1,067
    08-21-2017, 08:26 AM Go to last post

Page 1 of 30 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands