Hypertherm Plasma


Page 1 of 30 123411 ... LastLast
Threads 1 to 20 of 593

Forum: Hypertherm Plasma

Discuss hypertherm plasma machines here.

  1. Powermax 30XP + Plasmacam

    Started by phuffman‎, 11-15-2017 12:19 AM
    30xp, airlines/compressor, plasmacam, powermax, system
    • Replies: 1
    • Views: 181
    11-15-2017, 12:11 PM Go to last post
  2. Plasma tip dragging on steel

    Started by mrobs‎, 11-10-2017 09:13 AM
    cut, drags, part, plasma, tip
    • Replies: 2
    • Views: 151
    11-10-2017, 11:25 AM Go to last post
  3. Burning Countersunk Holes

    Started by Stovtop‎, 11-08-2017 11:04 AM
    counter, holes, square, sunk, wondering
    • Replies: 0
    • Views: 104
    11-08-2017, 11:04 AM Go to last post
  4. Grey electrodes, Hypertherm Powermax 105

    Started by Fyresparxx‎, 10-06-2017 11:07 AM
    • Replies: 2
    • Views: 430
    10-06-2017, 12:06 PM Go to last post
  5. CPC PORT VOLTAGE DIVIDER SOURCE CURRENT

    Started by cristobalmunoz‎, 09-30-2017 05:58 PM
    cpc, divider, specifications, voltage
    • Replies: 1
    • Views: 239
    10-01-2017, 09:41 AM Go to last post
  6. Need Help!- HYPERTHERM MAX200 TORCH HARD ARC STATING

    Started by yahya990‎, 09-21-2017 10:45 PM
    • Replies: 2
    • Views: 180
    09-27-2017, 09:49 AM Go to last post
    • Replies: 6
    • Views: 3,154
    09-23-2017, 04:12 PM Go to last post
  7. Need Help!- Bad Dross Fine Cut Powermax 105

    Started by Fyresparxx‎, 09-08-2017 07:16 PM
    • Replies: 8
    • Views: 349
    09-19-2017, 10:09 AM Go to last post
    • Replies: 1
    • Views: 204
    09-19-2017, 07:57 AM Go to last post
  8. Are these original hypertherm spare partes?

    Started by mzerighi‎, 08-24-2017 06:13 AM
    • Replies: 7
    • Views: 354
    09-17-2017, 08:08 AM Go to last post
  9. Need Help!- Hypertherm MAX42 torch retrofit

    Started by pmdgoncal‎, 09-08-2017 06:23 PM
    comments, max, max42, pedro, torch
    • Replies: 1
    • Views: 179
    09-11-2017, 06:38 PM Go to last post
  10. Help with torch installation

    Started by Spitterkat‎, 09-07-2017 06:03 PM
    height, installed, pierce, set, torch
    • Replies: 0
    • Views: 134
    09-07-2017, 06:03 PM Go to last post
  11. Red face Need Help!- Hypertherm Sensor Torch Height Control

    Started by francis_liang‎, 02-16-2017 01:52 AM
    arc, problem, sensor, thc, torch
    • Replies: 4
    • Views: 988
    08-21-2017, 08:26 AM Go to last post
  12. Need Help!- hypertherm powermax65 issue

    Started by josevsalcedo‎, 08-07-2017 05:39 PM
    • Replies: 0
    • Views: 237
    08-07-2017, 05:39 PM Go to last post
  13. Need Help!- Power supply to hypertherm power source

    Started by rajan_dd‎, 07-18-2017 01:36 AM
    drive, 480v, 60hz, power, supply
    • Replies: 0
    • Views: 174
    07-18-2017, 01:36 AM Go to last post
  14. Need Help!- hd1070

    Started by markirow‎, 07-16-2017 04:05 AM
    illuminates, led, plasma, transformer, written
    • Replies: 1
    • Views: 250
    07-16-2017, 09:57 AM Go to last post
  15. Need Help!- supply voltage of HD4070 078087

    Started by rajan_dd‎, 07-13-2017 02:16 PM
    • Replies: 2
    • Views: 174
    07-15-2017, 04:57 PM Go to last post
  16. powermaz 45 issues(?)

    Started by Thermwood‎, 07-14-2017 12:24 PM
    • Replies: 2
    • Views: 170
    07-14-2017, 01:13 PM Go to last post
  17. air shield treatment

    Started by rhinocut‎, 07-09-2017 06:52 AM
    air, compressor, filter, shield, unnecessary
    • Replies: 2
    • Views: 203
    07-09-2017, 08:47 PM Go to last post
  18. argon marking with a 260xd

    Started by rhinocut‎, 07-09-2017 06:34 AM
    260xd, argon, beast, machine, marking
    • Replies: 2
    • Views: 181
    07-09-2017, 08:42 PM Go to last post

Page 1 of 30 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands