Hypertherm Plasma


Page 1 of 30 123411 ... LastLast
Threads 1 to 20 of 594

Forum: Hypertherm Plasma

Discuss hypertherm plasma machines here.

  1. Need Help!- Connecting PowerMax 65 to Chinese THC and Controller

    Started by kamkama‎, Yesterday 05:29 PM
    • Replies: 0
    • Views: 67
    Yesterday, 05:29 PM Go to last post
  2. Powermax 30XP + Plasmacam

    Started by phuffman‎, 11-15-2017 12:19 AM
    30xp, airlines/compressor, plasmacam, powermax, system
    • Replies: 1
    • Views: 384
    11-15-2017, 12:11 PM Go to last post
  3. Plasma tip dragging on steel

    Started by mrobs‎, 11-10-2017 09:13 AM
    cut, drags, part, plasma, tip
    • Replies: 2
    • Views: 169
    11-10-2017, 11:25 AM Go to last post
  4. Burning Countersunk Holes

    Started by Stovtop‎, 11-08-2017 11:04 AM
    counter, holes, square, sunk, wondering
    • Replies: 0
    • Views: 122
    11-08-2017, 11:04 AM Go to last post
  5. Grey electrodes, Hypertherm Powermax 105

    Started by Fyresparxx‎, 10-06-2017 11:07 AM
    • Replies: 2
    • Views: 450
    10-06-2017, 12:06 PM Go to last post
  6. CPC PORT VOLTAGE DIVIDER SOURCE CURRENT

    Started by cristobalmunoz‎, 09-30-2017 05:58 PM
    cpc, divider, specifications, voltage
    • Replies: 1
    • Views: 252
    10-01-2017, 09:41 AM Go to last post
  7. Need Help!- HYPERTHERM MAX200 TORCH HARD ARC STATING

    Started by yahya990‎, 09-21-2017 10:45 PM
    • Replies: 2
    • Views: 195
    09-27-2017, 09:49 AM Go to last post
    • Replies: 6
    • Views: 3,188
    09-23-2017, 04:12 PM Go to last post
  8. Need Help!- Bad Dross Fine Cut Powermax 105

    Started by Fyresparxx‎, 09-08-2017 07:16 PM
    • Replies: 8
    • Views: 378
    09-19-2017, 10:09 AM Go to last post
    • Replies: 1
    • Views: 226
    09-19-2017, 07:57 AM Go to last post
  9. Are these original hypertherm spare partes?

    Started by mzerighi‎, 08-24-2017 06:13 AM
    • Replies: 7
    • Views: 362
    09-17-2017, 08:08 AM Go to last post
  10. Need Help!- Hypertherm MAX42 torch retrofit

    Started by pmdgoncal‎, 09-08-2017 06:23 PM
    comments, max, max42, pedro, torch
    • Replies: 1
    • Views: 185
    09-11-2017, 06:38 PM Go to last post
  11. Help with torch installation

    Started by Spitterkat‎, 09-07-2017 06:03 PM
    height, installed, pierce, set, torch
    • Replies: 0
    • Views: 145
    09-07-2017, 06:03 PM Go to last post
  12. Red face Need Help!- Hypertherm Sensor Torch Height Control

    Started by francis_liang‎, 02-16-2017 01:52 AM
    arc, problem, sensor, thc, torch
    • Replies: 4
    • Views: 1,017
    08-21-2017, 08:26 AM Go to last post
  13. Need Help!- hypertherm powermax65 issue

    Started by josevsalcedo‎, 08-07-2017 05:39 PM
    • Replies: 0
    • Views: 243
    08-07-2017, 05:39 PM Go to last post
  14. Need Help!- Power supply to hypertherm power source

    Started by rajan_dd‎, 07-18-2017 01:36 AM
    drive, 480v, 60hz, power, supply
    • Replies: 0
    • Views: 180
    07-18-2017, 01:36 AM Go to last post
  15. Need Help!- hd1070

    Started by markirow‎, 07-16-2017 04:05 AM
    illuminates, led, plasma, transformer, written
    • Replies: 1
    • Views: 278
    07-16-2017, 09:57 AM Go to last post
  16. Need Help!- supply voltage of HD4070 078087

    Started by rajan_dd‎, 07-13-2017 02:16 PM
    • Replies: 2
    • Views: 180
    07-15-2017, 04:57 PM Go to last post
  17. powermaz 45 issues(?)

    Started by Thermwood‎, 07-14-2017 12:24 PM
    • Replies: 2
    • Views: 176
    07-14-2017, 01:13 PM Go to last post
  18. air shield treatment

    Started by rhinocut‎, 07-09-2017 06:52 AM
    air, compressor, filter, shield, unnecessary
    • Replies: 2
    • Views: 208
    07-09-2017, 08:47 PM Go to last post

Page 1 of 30 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 14 users browsing this forum. (0 members & 14 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands