HURCO

Page 1 of 81 12341151 ... LastLast
Threads 1 to 20 of 1615

Forum: HURCO

Discuss Hurco machines here.

  1. "Chip Remover".....

    Started by Bluegillman‎, 02-03-2011 09:33 PM
    • Replies: 3
    • Views: 1,420
    02-04-2011, 10:11 PM Go to last post
    • Replies: 15
    • Views: 1,617
    09-05-2021, 07:47 AM Go to last post
  2. Need Help!- "power cabinet temp too high"

    Started by umairelect‎, 03-23-2017 06:30 AM
    cabinet, high, machine, power, temp
    • Replies: 2
    • Views: 1,746
    03-24-2017, 10:18 AM Go to last post
  3. "reversed encoder phase detected on axis z"

    Started by MAM00‎, 07-20-2017 05:44 AM
    axis, detected, encoder, phase, reversed
    • Replies: 0
    • Views: 402
    07-20-2017, 05:44 AM Go to last post
  4. Problem- "Security Device Invalid or Has Failed"

    Started by xray34‎, 08-02-2010 03:04 PM
    another, down, its, next, said, took
    • Replies: 1
    • Views: 2,176
    08-03-2010, 04:16 PM Go to last post
  5. Need Help!- '91 Hurco BMC 20 Axis S Encoder Fault

    Started by WoodallMFG‎, 12-06-2019 12:18 PM
    axis fault, encoder, hurco, machine, spindle
    • Replies: 3
    • Views: 1,079
    12-08-2019, 12:41 AM Go to last post
  6. Newbie- (Face milling/ Hurco WM10i) What is x corner and y corner?

    Started by 71gordi‎, 04-22-2021 01:11 PM
    appreciated, corner, face, mill, milling
    • Replies: 1
    • Views: 748
    04-22-2021, 10:20 PM Go to last post
  7. *OLD* Hurco knee mill

    Started by fasto‎, 06-27-2011 11:01 PM
    look, not
    • Replies: 8
    • Views: 2,818
    11-28-2011, 11:25 AM Go to last post
  8. Need Help!- .HNC

    Started by stevieboy‎, 07-30-2010 05:12 PM
    away, everyone, went
    • Replies: 10
    • Views: 3,409
    08-01-2010, 05:12 PM Go to last post
  9. 02 Hawk 40 start position issue

    Started by Hawk40‎, 02-01-2019 04:49 AM
    • Replies: 1
    • Views: 687
    03-24-2019, 11:14 AM Go to last post
  10. New Machine Build- 1978?? Hurco M1

    Started by Metzenw‎, 01-08-2016 01:51 PM
    centroid, guys, machine, pictures, worth
    • Replies: 4
    • Views: 874
    01-09-2016, 12:13 PM Go to last post
  11. 1979 Hurco Basics

    Started by schmold‎, 12-01-2010 01:43 PM
    look, not
    • Replies: 4
    • Views: 1,369
    12-02-2010, 04:05 AM Go to last post
  12. 1986 BMC-10 control panel dead

    Started by JThomsen‎, 01-19-2013 10:39 AM
    cabine, cor, down, except, its, look, next, went
    • Replies: 1
    • Views: 843
    01-19-2013, 04:48 PM Go to last post
  13. Need Help!- 1989 km3p x axis problem

    Started by ABFrank‎, 08-12-2015 07:05 AM
    • Replies: 9
    • Views: 1,863
    10-14-2015, 09:00 AM Go to last post
  14. Unhappy Problem- 1994 HURCO BMC 30 - System Resets itself

    Started by musnar‎, 04-27-2011 09:47 AM
    goes, not
    • Replies: 0
    • Views: 1,282
    04-27-2011, 09:47 AM Go to last post
  15. 1995 Hawk 5 value....

    Started by ChipKing‎, 01-29-2010 06:23 PM
    away, cor, goes, maybe, non, sinkers, then
    • Replies: 1
    • Views: 1,068
    01-29-2010, 10:27 PM Go to last post
  16. 1998 Hurco BMC 4020 through 8' door

    Started by J5klein1‎, 08-06-2018 11:53 PM
    posts, door, foot, wondering, easily
    • Replies: 0
    • Views: 538
    08-06-2018, 11:53 PM Go to last post
  17. Need Help!- 1999 Hurco BMC 4020 - Calibration Problem

    Started by hkenuam‎, 03-01-2015 11:18 AM
    • Replies: 17
    • Views: 4,433
    03-10-2015, 10:20 AM Go to last post
  18. 2 hurco KM3P

    Started by BenDiesel‎, 03-06-2021 07:54 PM
    • Replies: 1
    • Views: 354
    03-09-2021, 12:36 PM Go to last post

Page 1 of 81 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 17 users browsing this forum. (0 members & 17 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands