Hitachi Seikis

Page 1 of 12 123411 ... LastLast
Threads 1 to 20 of 225

Forum: Hitachi Seikis

Discuss Hitachi Seikis here!

  1. Hitachi Seikis VK45 II - Seicos M3 - Error 867

    Started by firstreal‎, Yesterday 06:37 AM
    • Replies: 0
    • Views: 58
    Yesterday, 06:37 AM Go to last post
  2. Need Help!- 5NE-1100

    Started by juanfmoralese‎, 02-13-2018 11:12 PM
    5ne-1100, control, fanuc, lathe, seiki
    • Replies: 0
    • Views: 118
    02-13-2018, 11:12 PM Go to last post
  3. Hitachi Seiki Repair / Service / Support

    Started by shas595‎, 06-15-2015 10:31 AM
    3 Pages
    1 2 3
    • Replies: 32
    • Views: 2,093
    02-05-2018, 10:05 AM Go to last post
  4. Exclamation Problem- Hitachi 23B hicell Seicos LIII not working

    Started by xxx83‎, 12-26-2017 02:06 PM
    • Replies: 11
    • Views: 442
    01-19-2018, 03:06 AM Go to last post
  5. Need Help!- Hitachi Seiki HC400 All Over Travel Alarm

    Started by Billet Carb‎, 01-16-2018 05:21 PM
    hc 400 overtravel alarms, machine, problem, received, voltage
    • Replies: 0
    • Views: 129
    01-16-2018, 05:21 PM Go to last post
  6. Problem- Hitachi Seiki 3 NE -300

    Started by Falcone‎, 01-11-2018 11:21 AM
    deleted, hitachi, program, programs, seiki
    • Replies: 2
    • Views: 143
    01-11-2018, 11:38 AM Go to last post
  7. Seicos III, battery dead? software reload? How bad is this?

    Started by bob1112‎, 09-06-2017 10:29 PM
    2 Pages
    1 2
    battery, dead, pretty, reload, software
    • Replies: 14
    • Views: 466
    12-13-2017, 05:54 PM Go to last post
    • Replies: 0
    • Views: 177
    12-06-2017, 04:08 PM Go to last post
  8. Question Need Help!- Hitachi Seiki Hicell 23B CNC Lathe Seicos LIII

    Started by Kutina-THK‎, 11-23-2017 09:29 AM
    • Replies: 1
    • Views: 334
    11-27-2017, 08:26 AM Go to last post
  9. Need Help!- VK 45 parameters

    Started by murrayadams‎, 11-20-2017 01:44 AM
    diagnostic, parameter, parameters, photos, screen
    • Replies: 3
    • Views: 209
    11-22-2017, 08:11 AM Go to last post
  10. Need Help!- Hitachi Seiki 5NF-800

    Started by JeanLuiz‎, 10-09-2017 02:06 PM
    5 Pages
    1 2 3 4 5
    • Replies: 53
    • Views: 1,074
    11-21-2017, 05:41 PM Go to last post
  11. Need Help!- Anyone have a HT-20 w/ Fanuc 3T-F? need info!

    Started by captianpattson‎, 11-13-2017 08:08 PM
    • Replies: 0
    • Views: 209
    11-13-2017, 08:08 PM Go to last post
    • Replies: 1
    • Views: 139
    11-13-2017, 10:02 AM Go to last post
  12. Need Help!- drip feed on hitachi vk45

    Started by murrayadams‎, 11-15-2015 04:19 AM
    computer, drip, feed, tape, vk45
    • Replies: 4
    • Views: 925
    11-12-2017, 10:51 PM Go to last post
  13. Hitachi TS15 Turret reset procedure

    Started by docdesigns‎, 08-27-2017 10:45 AM
    belt, hitachi, index, timing, turret
    • Replies: 4
    • Views: 313
    10-20-2017, 03:41 PM Go to last post
  14. Newbie- 20slldoes not feed

    Started by lerardi‎, 10-14-2017 12:23 PM
    cnc, feed, information, tapatalk, iphone
    • Replies: 1
    • Views: 149
    10-16-2017, 08:10 AM Go to last post
  15. Need Help!- 5NF-800

    Started by JeanLuiz‎, 10-12-2017 02:43 PM
    cnc, 561-305-0544, computer, 5nf-800, thal
    • Replies: 0
    • Views: 152
    10-12-2017, 02:43 PM Go to last post
  16. Need Help!- VK45 - Seicos III - Tape RS232C

    Started by firstreal‎, 10-07-2017 03:02 AM
    cnc, rs232c, send, start, transmission
    • Replies: 4
    • Views: 280
    10-12-2017, 03:49 AM Go to last post
    • Replies: 1
    • Views: 283
    10-09-2017, 03:28 PM Go to last post
  17. Clamp and unclamp

    Started by sml2010‎, 06-25-2017 03:45 AM
    4th, 5th, axis, clamp, unclamp
    • Replies: 1
    • Views: 333
    10-09-2017, 03:23 PM Go to last post

Page 1 of 12 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands