TS15 Turret Index Error After Power Cycle

Results 1 to 5 of 5

Thread: TS15 Turret Index Error After Power Cycle

  1. #1
    Registered
    Join Date
    Jan 2016
    Location
    United States
    Posts
    1
    Downloads
    0
    Uploads
    0

    Unhappy TS15 Turret Index Error After Power Cycle

    First off, great forum/community!

    My Hitachi Seiki TS15 lathe APC battery was replaced. After that, turret position was off and threw an index error. I would then move the turret by hand to T01 (could feel a pin sliding into place), remove the APC battery, set parameter 1815 bit-4 to 1, power off/on, MDI T0100 (turret makes a clicking sound), and turret position is OK and machine runs as normal. THen when I power off/on, the turret will index 2-3 positions beyond, throw an error and turret indexing is jerky. I do the same process again and the turret and machines runs fine until it gets powered off.

    It seems that the turret is losing some position memory after power-off. The APC battery is new and no errors/warnings are generate. Nothing needed to be re-aligned after the battery change but am I missing a step? Any help or ideas will be greatly appreciated!



  2. #2
    Member shas595's Avatar
    Join Date
    Dec 2009
    Location
    United States
    Posts
    539
    Downloads
    0
    Uploads
    0

    Default Re: TS15 Turret Index Error After Power Cycle

    You also need to change PRM1015 and K00.3 from to do this procedure correctly. PM me if you still need help and I can send you some procedures on how to do fix this.

    John



  3. #3
    Registered
    Join Date
    Apr 2013
    Location
    United States
    Posts
    24
    Downloads
    0
    Uploads
    0

    Default Re: TS15 Turret Index Error After Power Cycle

    Any further progress with this. I am having the same issue with the same machine.



  4. #4
    *Registered User* EvoLEngineering's Avatar
    Join Date
    Jan 2019
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Hi. I have this issue again. Can someone send me the procedure?



  5. #5
    Member shas595's Avatar
    Join Date
    Dec 2009
    Location
    United States
    Posts
    539
    Downloads
    0
    Uploads
    0

    Default Re: TS15 Turret Index Error After Power Cycle

    Sent to your email - take a look

    John



  6. #6
    Junior Member MGV's Avatar
    Join Date
    Jan 2019
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Looks I have similar problem:
    Please, advise how to reset Alarm 2011 (Index Not Ready) on Amera Seiki Fanuc O T
    Axis Z, X movable. Machine goes to HP. Turret not rotating Spindle not rotating.
    Spindle servo shows -- not 00



  7. #7

    Default Re: TS15 Turret Index Error After Power Cycle

    Quote Originally Posted by shas595 View Post
    Sent to your email - take a look

    John
    john please concact me very urgent!!! hasanotomasyon@hotmail.com



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

TS15 Turret Index Error After Power Cycle

TS15 Turret Index Error After Power Cycle