Hardinge Lathes


Page 1 of 25 123411 ... LastLast
Threads 1 to 20 of 497

Forum: Hardinge Lathes

Discuss Hardinge Lathes here.

  1. Need Help!- Spindle not stopping

    Started by moonman5‎, 11-14-2017 01:55 PM
    converter, machine, phase, stop, tool
    • Replies: 0
    • Views: 282
    11-14-2017, 01:55 PM Go to last post
  2. Need Help!- Fanuc 21T G76 Improper G-Code

    Started by stevemastercam‎, 10-11-2017 04:53 PM
    010 alarm, 21t, fanuc, g76, improper g code
    • Replies: 3
    • Views: 281
    11-10-2017, 07:55 PM Go to last post
  3. New Machine Build- Hardinge HC. any CNC kits out there?

    Started by rodlouvers‎, 10-01-2017 03:53 PM
    cnc, hardinge, hardinge hc, kits
    • Replies: 1
    • Views: 210
    11-09-2017, 07:30 AM Go to last post
  4. Cool Hardinge HC Chucker Lathe Spindle Bearings

    Started by Bertman1‎, 11-07-2017 02:39 PM
    bearings, chucker, hardinge, lathe, spindle
    • Replies: 0
    • Views: 113
    11-07-2017, 02:39 PM Go to last post
  5. HARDINGE CHNC 1 WIRING SCHEMATIC

    Started by moonman5‎, 02-07-2017 07:12 AM
    • Replies: 9
    • Views: 805
    10-27-2017, 02:41 PM Go to last post
  6. Angry Need Help!- Quest 8/51 1053 e torque limiter fault wont reset

    Started by bschris‎, 10-19-2017 08:26 AM
    8-37, hardinge e axis, powered, reset, times
    • Replies: 0
    • Views: 162
    10-19-2017, 08:26 AM Go to last post
  7. Conquest 42 Bar feeder wiring

    Started by southcen‎, 09-22-2017 09:39 AM
    bar, conquest, feeder, information, spacesaver
    • Replies: 6
    • Views: 351
    10-10-2017, 10:49 AM Go to last post
  8. Need Help!- Fanuc O-T RS232. Cannot send from CNC to PC (capture)

    Started by K_Labs‎, 06-16-2017 04:21 PM
    baud, cnc, fanuc, o-t, rate
    • Replies: 4
    • Views: 464
    10-09-2017, 03:47 PM Go to last post
  9. Need Help!- Hi all

    Started by Goran_M‎, 08-30-2017 08:02 AM
    conquest, machine, optional, system, type
    • Replies: 2
    • Views: 360
    09-27-2017, 07:45 AM Go to last post
  10. Hardinge CHNC 1 Allen Bradley Tape Reader not reading

    Started by ThiloD‎, 09-21-2017 04:36 PM
    • Replies: 0
    • Views: 81
    09-21-2017, 04:36 PM Go to last post
  11. Need Help!- 2007 GT-27(chnc) no power up

    Started by DetProto‎, 09-12-2017 02:55 PM
    battery, control, machine, power, screen
    • Replies: 0
    • Views: 210
    09-12-2017, 02:55 PM Go to last post
  12. please, looking for opinions about talent 51 msy

    Started by deadlykitten‎, 09-12-2017 10:22 AM
    direct, lathe, msy, posts, talent
    • Replies: 0
    • Views: 169
    09-12-2017, 10:22 AM Go to last post
  13. CHNC 1

    Started by Lpmach‎, 09-09-2017 04:36 AM
    block, chnc, light, push, single
    • Replies: 1
    • Views: 195
    09-11-2017, 04:50 PM Go to last post
  14. G4 T0101

    Started by Welder2022‎, 08-25-2017 12:51 PM
    command, purpose, t0101, tool, tool change
    • Replies: 0
    • Views: 161
    08-25-2017, 12:51 PM Go to last post
  15. CS42 SUB SPINDLE DRIVE

    Started by Welder2022‎, 07-04-2017 01:54 PM
    • Replies: 3
    • Views: 469
    08-09-2017, 07:41 AM Go to last post
  16. Cobra 51 question

    Started by joeyjrc‎, 08-05-2017 08:40 AM
    cnc, cobra, count, find, part
    • Replies: 3
    • Views: 300
    08-07-2017, 11:44 AM Go to last post
    • Replies: 0
    • Views: 131
    08-05-2017, 08:33 AM Go to last post
  17. HARDINGE CHNC LATHE GENRAL NUMERIC CONTROL

    Started by moonman5‎, 02-05-2017 01:06 PM
    2 Pages
    1 2
    chnc, control, hardinge, numeric, overloading
    • Replies: 13
    • Views: 756
    08-02-2017, 11:09 AM Go to last post
  18. Problem- CHNC II Component Locations

    Started by glbreil‎, 07-29-2017 10:43 PM
    component, diagram, knowledge, locations, thought
    • Replies: 0
    • Views: 170
    07-29-2017, 10:43 PM Go to last post

Page 1 of 25 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (1 members & 4 guests)

  1. MCPartsKid

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands