Hardinge Lathes


Page 1 of 25 123411 ... LastLast
Threads 1 to 20 of 495

Forum: Hardinge Lathes

Discuss Hardinge Lathes here.

  1. Angry Need Help!- Quest 8/51 1053 e torque limiter fault wont reset

    Started by bschris‎, 10-19-2017 07:26 AM
    8-37, hardinge e axis, powered, reset, times
    • Replies: 0
    • Views: 87
    10-19-2017, 07:26 AM Go to last post
  2. Need Help!- Fanuc 21T G76 Improper G-Code

    Started by stevemastercam‎, 10-11-2017 03:53 PM
    010 alarm, 21t, fanuc, g76, improper g code
    • Replies: 0
    • Views: 130
    10-11-2017, 03:53 PM Go to last post
  3. Conquest 42 Bar feeder wiring

    Started by southcen‎, 09-22-2017 08:39 AM
    bar, conquest, feeder, information, spacesaver
    • Replies: 6
    • Views: 305
    10-10-2017, 09:49 AM Go to last post
  4. Need Help!- Fanuc O-T RS232. Cannot send from CNC to PC (capture)

    Started by K_Labs‎, 06-16-2017 03:21 PM
    baud, cnc, fanuc, o-t, rate
    • Replies: 4
    • Views: 441
    10-09-2017, 02:47 PM Go to last post
  5. New Machine Build- Hardinge HC. any CNC kits out there?

    Started by rodlouvers‎, 10-01-2017 02:53 PM
    cnc, hardinge, hardinge hc, kits
    • Replies: 0
    • Views: 120
    10-01-2017, 02:53 PM Go to last post
  6. Need Help!- Hi all

    Started by Goran_M‎, 08-30-2017 07:02 AM
    conquest, machine, optional, system, type
    • Replies: 2
    • Views: 334
    09-27-2017, 06:45 AM Go to last post
  7. Hardinge CHNC 1 Allen Bradley Tape Reader not reading

    Started by ThiloD‎, 09-21-2017 03:36 PM
    • Replies: 0
    • Views: 61
    09-21-2017, 03:36 PM Go to last post
  8. Need Help!- 2007 GT-27(chnc) no power up

    Started by DetProto‎, 09-12-2017 01:55 PM
    battery, control, machine, power, screen
    • Replies: 0
    • Views: 183
    09-12-2017, 01:55 PM Go to last post
  9. please, looking for opinions about talent 51 msy

    Started by deadlykitten‎, 09-12-2017 09:22 AM
    direct, lathe, msy, posts, talent
    • Replies: 0
    • Views: 131
    09-12-2017, 09:22 AM Go to last post
  10. CHNC 1

    Started by Lpmach‎, 09-09-2017 03:36 AM
    block, chnc, light, push, single
    • Replies: 1
    • Views: 170
    09-11-2017, 03:50 PM Go to last post
  11. G4 T0101

    Started by Welder2022‎, 08-25-2017 11:51 AM
    command, purpose, t0101, tool, tool change
    • Replies: 0
    • Views: 152
    08-25-2017, 11:51 AM Go to last post
  12. CS42 SUB SPINDLE DRIVE

    Started by Welder2022‎, 07-04-2017 12:54 PM
    • Replies: 3
    • Views: 457
    08-09-2017, 06:41 AM Go to last post
  13. Cobra 51 question

    Started by joeyjrc‎, 08-05-2017 07:40 AM
    cnc, cobra, count, find, part
    • Replies: 3
    • Views: 283
    08-07-2017, 10:44 AM Go to last post
    • Replies: 0
    • Views: 109
    08-05-2017, 07:33 AM Go to last post
  14. HARDINGE CHNC LATHE GENRAL NUMERIC CONTROL

    Started by moonman5‎, 02-05-2017 12:06 PM
    2 Pages
    1 2
    chnc, control, hardinge, numeric, overloading
    • Replies: 13
    • Views: 699
    08-02-2017, 10:09 AM Go to last post
  15. Problem- CHNC II Component Locations

    Started by glbreil‎, 07-29-2017 09:43 PM
    component, diagram, knowledge, locations, thought
    • Replies: 0
    • Views: 164
    07-29-2017, 09:43 PM Go to last post
  16. Unhappy Need Help!- Please Help! Electrical Schematic Hardinge HC CHJ-8220

    Started by ToecutterUK‎, 07-18-2017 08:07 AM
    chj 8220, diagram, hardinge hc, schematic, volt
    • Replies: 0
    • Views: 172
    07-18-2017, 08:07 AM Go to last post
  17. Hardinge Conquest T42SP sub spindle dead

    Started by fadality‎, 06-26-2017 07:09 PM
    conquest, hardinge, spindle, t42sp
    • Replies: 1
    • Views: 200
    07-01-2017, 03:24 PM Go to last post
  18. HARDINGE CHNC 1 WIRING SCHEMATIC

    Started by moonman5‎, 02-07-2017 06:12 AM
    • Replies: 7
    • Views: 547
    06-16-2017, 12:37 PM Go to last post

Page 1 of 25 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 6 users browsing this forum. (0 members & 6 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands