Results 1 to 10 of 10

Thread: Post processor for HAAS MiniMill2

  1. 03-11-2012, 01:24 PM #1
    Errors
    Errors is offline
    Registered
    Join Date
    Mar 2012
    Location
    Kazakhstan
    Posts
    2
    Downloads
    0
    Uploads
    0

    Post processor for HAAS MiniMill2

    Hi everyone!
    Please, if you have...! Where i can found Post processor for MiniMill2?

  3. 03-11-2012, 02:19 PM #2
    Machineit
    Machineit is online now
    Registered Machineit's Avatar
    Join Date
    Mar 2010
    Location
    USA
    Posts
    1063
    Downloads
    0
    Uploads
    0
    Post processor for what software?
    Haas VF-2, HA5C, Hardinge CHNC 1, BobCAD V23

  4. 03-12-2012, 07:31 AM #3
    gizmo_454
    gizmo_454 is offline
    Registered
    Join Date
    Feb 2007
    Location
    USA
    Posts
    318
    Downloads
    0
    Uploads
    0
    Most software manufacturers should have a post for the VF series or Haas. When it comes to a post for a Haas Mill, you should be able to use just about anything written for Mini Mills to big VF's. The control runs the same on all of them, using the same G and M codes.

    Mike

  5. 03-12-2012, 10:03 AM #4
    KenFoulks
    KenFoulks is offline
    Registered KenFoulks's Avatar
    Join Date
    Aug 2010
    Location
    USA
    Posts
    569
    Downloads
    0
    Uploads
    0

    Haas Factory Support

    Please check with your local Mastercam reseller, which I believe is in Russia.

    http://www.mastercam-russia.ru/
    Thanks,
    Ken Foulks
  6. Register to remove these Ads!

  • 03-12-2012, 11:55 AM #5
    WallyL7
    WallyL7 is offline
    Registered WallyL7's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    641
    Downloads
    0
    Uploads
    0
    Quote Originally Posted by KenFoulks View Post
    Please check with your local Mastercam reseller, which I believe is in Russia.
    He never said what software he has...lol
    Tim

  • 03-12-2012, 12:06 PM #6
    KenFoulks
    KenFoulks is offline
    Registered KenFoulks's Avatar
    Join Date
    Aug 2010
    Location
    USA
    Posts
    569
    Downloads
    0
    Uploads
    0
    Quote Originally Posted by WallyL7 View Post
    He never said what software he has...lol
    He has two posts so far, the other is in the Mastercam forum.
    Thanks,
    Ken Foulks

  • 03-12-2012, 12:23 PM #7
    WallyL7
    WallyL7 is offline
    Registered WallyL7's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    641
    Downloads
    0
    Uploads
    0
    I actually did see his other one just now...but thought he ought to at least clear up this one.

    Guys and their posts these days...
    Tim

  • 03-12-2012, 01:11 PM #8
    Machineit
    Machineit is online now
    Registered Machineit's Avatar
    Join Date
    Mar 2010
    Location
    USA
    Posts
    1063
    Downloads
    0
    Uploads
    0
    Quote Originally Posted by WallyL7 View Post
    He never said what software he has...lol
    Noticed that did you?!?!?!
    Haas VF-2, HA5C, Hardinge CHNC 1, BobCAD V23

  • 03-12-2012, 01:13 PM #9
    WallyL7
    WallyL7 is offline
    Registered WallyL7's Avatar
    Join Date
    Dec 2008
    Location
    USA
    Posts
    641
    Downloads
    0
    Uploads
    0
    Quote Originally Posted by Machineit View Post
    Noticed that did you?!?!?!
    lol - I figured Ken was psychic though.
    Tim

  • 03-12-2012, 01:16 PM #10
    Machineit
    Machineit is online now
    Registered Machineit's Avatar
    Join Date
    Mar 2010
    Location
    USA
    Posts
    1063
    Downloads
    0
    Uploads
    0
    Quote Originally Posted by WallyL7 View Post
    lol - I figured Ken was psychic though.
    Oops, I'll have to stop thinking some thoughts!!!!!!!
    Haas VF-2, HA5C, Hardinge CHNC 1, BobCAD V23

    • « locked keyboard not responding | Haas VF series transmission and final ratios? »

    Similar Threads

    1. haas sl post processor
      By busted bit in forum BobCad-Cam
      Replies: 2
      Last Post: 09-21-2012, 10:54 AM
    2. Need Help!- Haas VF2 Post Processor
      By Frebird0708 in forum CamWorks
      Replies: 0
      Last Post: 02-12-2012, 03:48 PM
    3. Need Help!- Haas post processor.
      By neilthib in forum Dolphin CADCAM
      Replies: 1
      Last Post: 10-28-2011, 08:52 PM
    4. HAAS Minimill2 Reviews??
      By Benji in forum Haas Mills
      Replies: 12
      Last Post: 10-12-2009, 11:41 PM
    5. Need post processor from Pro-E to Haas
      By PokeyTeacher in forum Post Processor Files
      Replies: 3
      Last Post: 02-25-2009, 10:02 PM

    Tags for this Thread

    View Tag Cloud

    Posting Permissions



    About CNCzone.com

      We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

    Recommended Links

    Quick Links

    Follow us on

    Facebook Dribbble RSS Feed


    Search Engine Friendly URLs by vBSEO ©2011, Crawlability, Inc.