Granite Devices

Page 1 of 11 1234 ... LastLast
Threads 1 to 20 of 214

Forum: Granite Devices

Discuss about servo & stepper drives made by Granevices and get direct support!

  1. Will Argon drive work with Sanyo motor

    Started by medu2015‎, 07-26-2016 12:34 PM
    • Replies: 2
    • Views: 1,268
    07-29-2016, 12:10 AM Go to last post
  2. Is Granite Devices out of business?

    Started by Black Forest‎, 07-06-2016 07:03 AM
    asked, business, devices, granite, replies
    • Replies: 6
    • Views: 786
    07-22-2016, 09:35 AM Go to last post
  3. VSD-E drives

    Started by jnnewton‎, 06-10-2016 07:53 AM
    buy, drives, sell, vsd-e
    • Replies: 0
    • Views: 445
    06-10-2016, 07:53 AM Go to last post
    • Replies: 0
    • Views: 1,036
    02-23-2016, 02:09 PM Go to last post
    • Replies: 0
    • Views: 1,006
    01-26-2016, 06:42 AM Go to last post
    • Replies: 0
    • Views: 832
    11-28-2015, 04:44 PM Go to last post
  4. I am a newbie, Argon drive with Mach 3?

    Started by machining fool‎, 08-18-2015 01:06 PM
    argon, centipede, correct, drive, setup
    • Replies: 0
    • Views: 1,317
    08-18-2015, 01:06 PM Go to last post
  5. Newbie needs help with VSD-XE drive.

    Started by machining fool‎, 08-18-2015 10:40 AM
    adept, cnc, ksi, newbie, servo
    • Replies: 0
    • Views: 731
    08-18-2015, 10:40 AM Go to last post
  6. Question 2 encoders on ARGON

    Started by TomBuil‎, 08-06-2015 08:02 AM
    argon, encoder, linear, motor, position
    • Replies: 0
    • Views: 771
    08-06-2015, 08:02 AM Go to last post
  7. Electronic gearing

    Started by EFI-Unlimited‎, 07-23-2015 10:00 PM
    create, drive, electronic, gearing, heavy
    • Replies: 4
    • Views: 923
    07-25-2015, 07:14 PM Go to last post
  8. Will Argon drive work with a more powerful servo?

    Started by richienz‎, 05-04-2015 07:33 PM
    argon, drive, give, prob, servo
    • Replies: 3
    • Views: 1,588
    05-24-2015, 08:41 PM Go to last post
  9. New IONI Servo Drive Indigogo campaign.

    Started by jschulze‎, 03-19-2015 11:34 AM
    campaign, drive, indigogo, ioni, servo
    • Replies: 0
    • Views: 1,268
    03-19-2015, 11:34 AM Go to last post
  10. VSD-E USB Cable

    Started by francp111‎, 01-20-2015 10:09 AM
    already, buy, cable, granite, pin, serial, usb, vsd, vsd-e, work
    • Replies: 2
    • Views: 1,010
    03-12-2015, 05:07 PM Go to last post
    • Replies: 2
    • Views: 1,999
    03-12-2015, 11:04 AM Go to last post
  11. Granite VSD-XE tuning

    Started by richienz‎, 02-09-2015 05:16 PM
    cnc, forum, position, posts, tune
    • Replies: 8
    • Views: 1,333
    02-17-2015, 08:06 PM Go to last post
  12. Need Help!- GDTool Torque Tuning Step Responce.

    Started by jtlapp‎, 02-02-2015 01:26 PM
    • Replies: 1
    • Views: 850
    02-03-2015, 10:59 PM Go to last post
  13. Need Help!- VSD-E dual DC, home switches?

    Started by Pairair‎, 11-25-2014 07:38 AM
    axis, board, breakout, breakout board, dual, home, home switches, ing, ning, one, run, running, swi, switches, vsd, vsd-e, vsdepi, way, whe, wire, y axis
    • Replies: 1
    • Views: 1,161
    02-03-2015, 01:14 PM Go to last post
  14. VSDE 160 BLDC problem

    Started by evo4wrx‎, 02-06-2010 09:52 PM
    3 Pages
    1 2 3
    down, far, goes, its, then
    • Replies: 35
    • Views: 7,502
    02-02-2015, 09:04 PM Go to last post
  15. SimpleMotion control library

    Started by Xerxes‎, 02-11-2010 05:53 PM
    3 Pages
    1 2 3
    • Replies: 32
    • Views: 10,927
    01-26-2015, 05:01 PM Go to last post
  16. Newbie- How would i wire a Argon with a Kanalog interface.

    Started by NeoTech‎, 01-26-2015 09:40 AM
    argon, encoder, kanalog, signal, software
    • Replies: 0
    • Views: 887
    01-26-2015, 09:40 AM Go to last post

Page 1 of 11 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands