z bavelloni egar 320

[capo nord]

there are planty of producers of good millings for exapme: Nicolai, Adi, Vincent, Diamut... the important thing is the diameter that should be max 20 mm. the working parameters are: 3000/5000 r.p.m. (spindle rotation), 0.1/0.4 mt/min (speed in meter per minute). another important thing is to have internal water with pressure 4/5 bar, 20/25 l/min (liter per minute) and recicled external water should have a precise direction on the tool. these parameters are for granite thickness 30 mm. all my customers are working with these parameters and are doing OK.
Ciao,
Fabio

[anhbao1205]

hi everyone ,
myname's Bao
my z-bavelloni have error " head out of position"
when it move , i chose parameters
please help me repair it

[anhbao1205]

Originally Posted by capo nord Hi everybody! do you still have problems with the pump? maybe I can help. I was a Bavelloni CNC technicain. Fabio

i have a glass z-bavelloni 372

when machine move , i clicked f7( paramaters) and chose visual marco utility .
then it don't move and have one error " head out of position"

i hope you can help me , soon by soon

i'll wait your mail
thanks a lot

[anhbao1205]

Originally Posted by capo nord Hi everybody! do you still have problems with the pump? maybe I can help. I was a Bavelloni CNC technicain. Fabio

hi!!1
i forget my mail
my mail is " tranvuong_anhbao@yahoo.com"
thanks agian

[capo nord]

Hi,
unfortunately I can not help as I am specialized only in the numerical control machines and not on cutting tables... sorry.
Ciao,
Fabio

[Counterguy]

Does anyone know where I can buy a left side bridge boot for an egar 320 at a reasonable price?

[capo nord]

sorry but I did not understand exactly what you're looking for

[Mark Smith]

Guys sorry for going off topic. Metro, you want to get my XXX red or my Yellow z5 >> http://www.nicolaidiamant.com/swf_ca...cnc/index.html Call with any questions.

[rocky1]

I powered up my Egar 320 this morning and got no lights or CRT image on the NC. The NC has power to it and the fan is running, but nothing else works. Is there a master reset? Could the MB be defective? I don't even know where to look. Help!

[bavcnc]

Originally Posted by rocky1 I powered up my Egar 320 this morning and got no lights or CRT image on the NC. The NC has power to it and the fan is running, but nothing else works. Is there a master reset? Could the MB be defective? I don't even know where to look. Help!

It could be that the back-up battery is gone. When you turn the power on, look at the top of the NC and see what lights come on. If you are getting no lights at all check the 24 VDC power supply.

Dan

[rocky1]

Fabio, I have an Egar 320 that we use to fabricate stone with. We have had epic problems with the water manifold for the past two years. I have replaced 7 water manifolds in less than 1000 hours on the machine. I think there is something causing the problem. Z Bav says they may have sold me a batch of bad manifolds. I cannot believe I'm the only one having this problem if that is the case. Can you enlighten me?

-joe

[rocky1]

Originally Posted by bavcnc It could be that the back-up battery is gone. When you turn the power on, look at the top of the NC and see what lights come on. If you are getting no lights at all check the 24 VDC power supply. Dan

There was a short in a wire that went to a safety switch on the vacuum pump. When the wire was shorted, it shut most of the machine down. We think there was a problem with one of the green modules where many of the wires are connected in the NC, so we replaced it, too. It was a difficult and expensive process to find this problem.

-joe