| | |
Conversion Tutorial for DC-K40 / TB6560 (blue board from Ebay) for Non-professionals Hello everybody,
After 6 months studying, learning, having help from friends and researching I finally successfully converted my Chinese DC-K40 machine to a TB6560 “blue board” to make it cut vectors with mach3.
That Moshi driver/Moshidraw did not work well, and do not cut vector files from ACad CorelDraw.
I first would like to say that I am a non-professional, but I understand a little about electronics, solder wires and mach3 software (this is the most difficult part)
This is a small thread showing all the steps I did to convert my machine. Like I´ve said: I AM NOT A PROFESSIONAL, and I`M NOT EARNING ANY $$$$ FOR THIS.
As a non-professional I´ll use a simple language to explain all the steps.
This is my machine´s conversion, and using a generic TB6560 board that I´ve bought from Ebay. Remember that your machine inner setup and board can be different from mine.
All hints from expert guys to improve other´s conversions would be welcome for this thread.
I´d like to apologize for my poor English, but I´ll do my best to show as much as pictures as necessary from the mach3 software setup and shots from my machine.
Some advises are import since it is a laser machine:
1-Always use laser goggles when the laser is working.
2-Always use laser goggles when the laser is working.
3-Always use laser goggles when the laser is working.
4-Always use laser goggles when the laser is working.
5-….
6-This is not a toy
7-Did you get it?
First of all you have to understand the basic: the TB6560 “blue board” is not a controller, it is a just a driver controlled by mach3 software. Mach3 software is the brain of all. The TB6560 board will be just a driver that will get all the information from mach3 and send to the stepper motors, and will receive information from the machine´s limit/home switches to send to the mach3. Period.
(I´m explaining it because I first thought that the TB6560 board was the controller, and I´m sure that most of the non-professional people thought same way)
I recommend a good read on mach 3´s manual since it will be the machine’s controller. G-Code (the code that mach3 use to do all the work) is not difficult to understand, but you have to spend some time studying like I did.
I will not explain mach3 to anyone. I will just show the setup page pictures.
Just for information; you will not need to change any wire that goes to the front panel; this panel will work as was working before the conversion. There we have a laser on/off pushbutton, a laser fire test button and a potentiometer that increases the laser power to cut a vast array of materials and thickness.
Remember: the TB6560 board will not control the laser fire; MACH3 will do that through the 25 pin serial port. Although the wires to control the laser fire will be soldered in the TB6560 board, it will just be a simple way to get the input from the 25 pin serial port.
You will see that I use the relay to turn on/off the laser (only in the beginning and ending of a work), it is just a safe procedure, and the relay do not control the laser trigger while the work is in progress. In the next lines you´ll see how it works.
So, lets start…
This is the picture of my laser machine arrangement:
Some machine´s arrangement are different from mine. If your machine is different from mine you will need some patience.
To make the DC-K40 work properly with a Tb6560 board we have to setup 4 stuff on the hardware: power up the TB6560 board with 24 volts, stepper motors, limit/home switches, and finally the laser trigger.
Powering the TB6560 board.
Take a look at the shot below:
Simple to do that, right? 24 volts from power source.
This “blue board” can bear up to 36 volts…
The stepper motors setup.
I´m not sure, but I guess my both stepper motors are Nema 17.
In a laser machine we don´t need strong motors since we don´t have a spindle that touch the piece that will be cut.
Take a look at the picture again:
Pay attention to the Axi´s wire setup and see that the wire sequence for X axis is different from Y axis sequence.
X axis sequence: Blue, Red, Yellow, White
Y axis sequence: Yellow, White, Blue, Red
You´ll need to extend the X axis wires because It too short to reach the board. To do that you´ll need around 20 inches long wires and a soldering iron.
On the picture above you´ll also see the dip micro switches setup for my Nema motors .
This is the setup I´m using.
-Current setting:
1-off
2-off
I have 25% of current to my motors
-Decay mode
3-on
4-on
I have FAST option to my motors
-Micro Step
5-off
6-on
1/16 microstep
On Mach 3…
…select config/ports and pins/motor outputs…
The picture below shows the pin/ports setup of my TB6560 driver. I followed the manual that came with my board. Yours can be different. I recommend to follow your board´s manual to setup the stepper motors ports and pins for X/Y axis.
Go to config/motor tuning:
These are the setup for steps/speed/acceleration for my X/Y axis Nema motors.
Ignore the Z axis setup for awhile, it will be explained in the laser fire.
Limit/home switches
You´ll need to buy 4 mechanical limit/home switches, because the machine´s limits are optical (I don´t think it work with the TB6560 blue board) and there are only 2 of it in the machine (only home switches, go figure why…)
The pictures bellow shows where I glued the 4 limit/home switches (I glued it with industrial silicon). You have thousands ways to install these switches.
My switches are “open circuit” models, and when they are activated it “short the circuit”.
This the setup I´m using in my machine:
On mach3 go to config/ports and pins/input signals, see the setup in the picture below:
In the same picture you see the option “Automated Setup of Inputs”. Click on it and select the switch/axis you want to setup. Read the Mach3´s user manual and you´ll see how to setup limit/home switches using this option.
Laser Setup:
*Don´t forget the goggles!
To fire the laser you´ll need to send from 3,3 to 5,0 volts to the laser power unit TH input. Where can I get these voltage??? From the 25 pin serial port.
I´m using the Mach3 Z axis action to send me this voltage. My computer works with 3,3volts, but the laser power source that came with my laser machine can work from 3,3 to 5,0 volts.
The picture bellow shows the way I get the signal from pin4 and ground of the 25 pin serial cable:
Setup dir pin4 in mach3 config/ports and pins/motors output
The Z setup above was the only one that worked, and it took some sleeping nights to find it out.
I had one problem: the dir pin4 was always sending 3,3 volts when the laser machine was stopped (before or after a project). If it is sending 3,3volts means that the laser is firing. The way I found to solve this problem was to use the spindle relay.
This is the wire setup from board to Laser PSU:
Go to config/ports and pins/output signals and setup like the picture below:
To make the relay active go to config/ports and pins/spindle setup, and follow the picture bellow:
On config/motor tuning you´ll need to set the maximum speed and acceleration for the Z axis, this way the laser will have the minimum delay.
There is a command to control the laser fire on mach 3 (using M10Px, M11Px) but it is a kind of complex and I prefer to use the Z axis to control it.
Don´t forget to use your goggles and turn on the water pump before turn on the laser.
If the laser do not work, check:
The config setup on your TB6560 users manual. Enable all pins and ports exactly like in the user´s manual.
The laser Switch push-button and the potentiometer on the machine´s main panel.
To convert the files from DXF to G-code files I´m using LazyCam software.
This is how I converted my Cheap Chinese CO2 laser machine.
If anyone have something to help improve this conversion it will be welcome.
Thank you
Raphael
http://www.youtube.com/watch?v=N6EHbkGb5lU]Cheap co2 laser machine + Mach3 + Cheap Ebay TB6560 board - YouTube
It was still without the limit/home switches and a laser big delay. Now I installed the switches and the delay is gone (by increasing the Z axis speed/acceleration)
I'm curious if you got the original board to work with the pc? I just recently bought a K40IV and just cant get the machine to get recognised by the PC, keeps saying unknown USB device. I have emailed the seller numerous times and they keep suggesting changing the USB ports which didn't help. I got fed up eventually and bought the DSP board from LightObject. Excellent post tho
Yes I did. But I can´t say it worked because it didn´t do anything I wanted (cut vectors, read vectors file and so). I learned how to draw in CorelDraw and than import to Moshi, but the cut was terrible.Originally Posted by 5by5laser
Chinese people do lots of stuff, I don´t understand why they don´t make a simple software to read and cut DXF files, instead that moshidraw; I´m 100% sure that they would sell twice more machine than they sell with moshidraw.
I know what you mean, I was telling my wife last night that Moshidraw software was up to version 9.90 and still they refuse to hire an english speaking person to do the translation after at least 9 versions. I was able to get the laser to talk to the pc by trying it on windows xp instead of 7 (which should work). The cuts were pretty bad, but hey atleast I know that all the parts are working as they should.
Nice! I also bought exactly this TB6560.
BUT My DC-K40iii (what ever that means) has a MoshiBoard 4.1. The 2 optical and one y-Motor are combined in one flat cable. And of course i want to use the optical swithes with the TB6560 board.
Also I read some other posts that the TB6560 needs some modifications to be a good board ... I have the 3 axis version as you do.
Hi guys. I have the same machine and the same components. I have a request, I need help with connected TB6560 with power supply (what the above post). I'm interested in the exact cable connection Relay 5V (MIN, GND, MOUT) with the power supply. Looking at the above post that I can not read where cable was going. THX
Posting Permissions
| | |
LinkBack URL
About LinkBacks
