| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| General Electronics Discussion Discuss basic electronics, power supplies and anything else electronic related here. |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#1
 
11-03-2007, 12:52 PM
| |||
| |||
Hi there guys, in between lurking round i've come up with a question of my own. I've been offered a very nice looking driver for my servo's.Now as being the perfect n00b i aint able to tell if this drive can be controlled by step&dir like mach and a "normal"pc. thx for listening(reading?).
__________________ Finally CHIPS you can have as much as you can without the doc. complainting about your cholesterol.    |
|
#2
11-03-2007, 01:17 PM
| ||||
| ||||
| The manual should tell you, your going to need it anyway in order to implement the drives, If I can't find a manual by search, I contact the manuf. support and often they send out something in PDF. In this case it would be Bosch/Rexroth/Indramat. Al.
__________________ “Logic will get you from A to B. Imagination will take you everywhere.” Albert E. (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
#3
11-04-2007, 06:20 PM
| |||
| |||
| I've been able to trach down a manual and step&dir ain't mentioned but maybe someone more experienced wouldn't mind having a looksee cause i'm probably overlooking something seem i can't seem to find out anything about software and or input signals. THX in advance guys.
__________________ Finally CHIPS you can have as much as you can without the doc. complainting about your cholesterol. |
|
#4
11-07-2007, 01:59 PM
| |||
| |||
| hmm... just no one in here that wants to be responsible for me electrocuting meself ? Cause i can't imagine no one knows. I was hoping a ready to go driver could save a n00b like me from electrocution way better then a self bake&glue project. And that should be the complete manual but i can't be dure since i D/Led. THX anyway.
__________________ Finally CHIPS you can have as much as you can without the doc. complainting about your cholesterol. |
|
#5
11-07-2007, 02:11 PM
| |||
| |||
| sorry guys
__________________ Finally CHIPS you can have as much as you can without the doc. complainting about your cholesterol. Last edited by ironDigit; 11-07-2007 at 02:12 PM. Reason: submitted twice(yeps ,that's one to many) |
| Sponsored Links |
| |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Parker pdx13 driver and step motor | Autocraft | Stepper Motors and Drives | 9 | 07-18-2007 10:34 AM |
| Drive a 2 phase servo with a step driver? | Eson | Stepper Motors and Drives | 0 | 02-23-2007 07:53 AM |
| Servo motor, step/dir driver and Mach. | Darc | Mach Mill | 0 | 04-11-2006 01:23 AM |
| Step Driver Open Source. Which is the best?? | Chivo | Open Source Controller Boards | 8 | 11-15-2005 05:26 PM |
| Pic Step driver V4 from ALAN | Chivo | Stepper Motors and Drives | 6 | 10-03-2005 07:15 PM |
| | |
Linear Mode
