LinkBack URL
About LinkBacks
did you got the drawings? Tell and then I will check if I can help!
Jawad
| | |
Looking to buy maintance drawings for wire edm with a A16B-1010-0210 MAIN BOARD .Allready tried Fanuc I was told that the drawings came with the machies when new .Would even consider buying a whole machine .Main board number is located at upper left corner of mother board .I have drawings for 6m control looking for OM-A control . Any help would be great .Also looking for parameters for same machine. The brake motor is a Mitsubushi partical brake that is 850.00 new its 24 volt would like to try a cheaper alternative .Any thoughts....?
did you got the drawings? Tell and then I will check if I can help!
Jawad
no i did not
I found my machine's Master PCB have this no. A16B-1010-0150.
I have fanuc tape cut w0. What model do you have?
Sent from my SGH-T959 using Tapatalk 2
I have a model..O ...iT Has a ...A16B1010-0210.....main board .AC digital drves and motors My machine uses the Om control I believe yours is a Oa control .
So do you have machine drawings ?
Yes, I've a hard copy of its Maintenance Drawings.
I'll consider to get it scanned if you need them.
I would pay you for a copy of the scan let me know .And thank you very much !
Mate, thank you very much for the offer. I will manage the scan expenses myself. However, I would require your help on another issue.
I have a Nomura NN-160D. I could not get its parameters. I contacted various people including OEM, Gosiger and the supplier to get the desired. Nomura Vtc Japan, the OEM refused to provide me the PDF file of the parameters even after quoting me the price. The reason he told that his company policy won't allow him to do any trade with Pakistan.
I can send you the complete communication for your reference.
I need your help to get those parameters and I'm not asking you to pay for me. I will pay you the quoted $70 approx. or whatever they demand.
This parameter thing have nothing to do with the manual you required.
Sent from my SGH-T959 using Tapatalk 2
I will see what I can do .I will tell you up front I am a Wre guy and I only work on fanuc controls .What control is on the machine in question , serial number , make and model . year of mfg .and any contact info .
> Following are the details of Nomura machine:
> - Model: NN-160 D
> (No of tools = 11)
> - No: 70109001
> - Type: FCA 310LN
> - Serial: m32745619
> - Date: 0X
This is how its written on the machine.
Here you can read the whole communication between me and OEMs guy:
From: "Shinya Asami" <s.asami@nomuravtc.co.jp>
Date: December 6, 2012 8:17:23 PM
Subject: RE: [Fwd: RE: FW: Nomura NN-160D....Parameters needed]
To: "'Info_JanjuaMetal'" <info@janjuametal.com>
Dear Mr. Jawad Hafeez,
Sorry, this is our company’s’ policy.
Even though this is just a soft copies. Really sorry.
Best regards,
Shinya Asami
****************************************************************************
NOMURA VTC AUTOMATIC LATHE CO., LTD.
SHINYA ASAMI (OVERSEAS BUSINESS DEPARTMENT)
437 TANAZAWA,OKUTAMA-MACHI, NI****AMA-GUN,TOKYO198-0106
TEL：(＋81)-428-85-1410 FAX：(＋81)-428-85-1418
http://www.nomuravtc.co.jp/english/
****************************************************************************
From: Info_JanjuaMetal [mailto:info@janjuametal.com]
Sent: Thursday, December 06, 2012 11:59 PM
To: Shinya Asami
Subject: RE: [Fwd: RE: FW: Nomura NN-160D....Parameters needed]
Dear Mr Shinya,
These are just soft copies.
Please consider what would we do without parameters with these machines.
You gave me hope, please make some way out.
Regards,
Jawad Hafeez
Sent with AquaMail for Android
http://www.aqua-mail.com
On December 6, 2012 7:29:05 PM "Shinya Asami" wrote:
Dear Mr. Jawad Hafeez,
I am sorry for not replying you sooner.
As our staff told you, I am on the business trip during this week.
I reported your inquiry to our management today,
but they told me that we cannot send the parameters to your area, Pakistan.
This is based on Japanese Export Control Regulations.
So we need to decline to provide you with it now.
We are sorry that we didn’t meet your expectation.
Best regards,
Shinya Asami
****************************************************************************
NOMURA VTC AUTOMATIC LATHE CO., LTD.
SHINYA ASAMI (OVERSEAS BUSINESS DEPARTMENT)
437 TANAZAWA,OKUTAMA-MACHI, NI****AMA-GUN,TOKYO198-0106
TEL：(＋81)-428-85-1410 FAX：(＋81)-428-85-1418
http://www.nomuravtc.co.jp/english/
****************************************************************************
From: info@janjuametal.com [mailto:info@janjuametal.com]
Sent: Wednesday, December 05, 2012 2:28 PM
To: info-m@nomuravtc.co.jp
Cc: s.asami@nomuravtc.co.jp ..
Subject: [Fwd: RE: FW: Nomura NN-160D. .Parameters needed]
Importance: High
As I've called to your phone office today, and was informed that Mr Shinya Asami will not be available till the end of this week.
Can anybody please address the below enquiry?
Regards,
Jawad Hafeez
---------------------------- Original Message ----------------------------
Subject: RE: FW: Nomura NN-160D....Parameters needed
From: info@janjuametal.com
Date: Fri, November 30, 2012 10:30 am
To: "shinya asami" <s.asami@nomuravtc.co.jp>
--------------------------------------------------------------------------
Dear Shinya Asami,
It's quite nice to hear that you still provide support even for the dated
Nomura machines.
We accept your below offer.
you can read more about us at www.janjuametal.com.
If you asking for our Bank information, I will let you know later from
where could I manage to transfer you the fee after getting your bank
details.
Kind regards,
Jawad Hafeez
> Dear Mr. Jawad Hafeez,
>
> Thank you for your quick respose.
> I do have the same parameter for your model.
>
> On our companys' policy, this parameter will be charged.
> Price : 1 set JPY7,000.- (PDF by email)
> Terms: T/T 100% in advance.
>
> If you accept our condition, please give us your reply again.
> I will provide you with our bank information.
> And I would like your copany information too.
>
> Best regards,
> Shinya Asami
> ****************************************************************************
> NOMURA VTC AUTOMATIC LATHE CO., LTD.
> SHINYA ASAMI (OVERSEAS BUSINESS DEPARTMENT)
>
> 437 TANAZAWA,OKUTAMA-MACHI, NI****AMA-GUN,TOKYO198-0106
> TEL$B!'(B($B!\(B81)-428-85-1410$B!!(BFAX$B!'(B($B!\(B81)-428-85-1418
> http://www.nomuravtc.co.jp/english/
> ****************************************************************************
>
> -----Original Message-----
>
From: info@janjuametal.com [mailto:info@janjuametal.com]
> Sent: Thursday, November 29, 2012 7:44 PM
> To: shinya asami
> Subject: Re: FW: Nomura NN-160D....Parameters needed
>
> Dear Mr/Ms Shinya Asami,
>
> Following are the details of one of our Nomura machines:
> (Do the same parameters/settings will work for both machines as they are
> identical?)
>
> - Model: NN-160 D
> (No of tools = 11)
> - No: 70109001
> - Type: FCA 310LN
> - Serial: m32745619
> - Date: 0X
>
> We., Janjua Metal Works (Pvt) Ltd., are a Small Manufacturing Enterprise
> in Pakistan and these machines are going to produce 'Clutch Lever
> Shafts' for Honda Motorbikes.
> We will be obliged to share more with you.
>
> Your earliest response will be highly appreciated,
>
> Kind regards,
> Jawad Hafeez
>
>
>>
>> Dear Mr.Jawad Haf,
>>
>> Thank you for contacting to us. And sorry for my late response.
>>
>> Could you please tell us the following?
>> 1. Machine Model
>> 2. Serial number
>> 3. Where did you install the machine?
>>
>> And please note that the parameters will be charged, not free of charge.
>> Your reply would be appreciated.
>>
>> Best regards,
>> Shinya Asami
>> **********************************************************************
>> ******
>> NOMURA VTC AUTOMATIC LATHE CO., LTD.
>> SHINYA ASAMI (OVERSEAS BUSINESS DEPARTMENT)
>>
>> 437 TANAZAWA,OKUTAMA-MACHI, NI****AMA-GUN,TOKYO198-0106
>>
> TEL$B!'(B($B!\(B81)-428-85-1410$B!!(BFAX$B!'(B($B!\(B81)-428
>> -85-
> 1418
>> http://www.nomuravtc.co.jp/english/
>> **********************************************************************
>> ******
>>
>>
>> ----- Original Message -----
>>
From: <info@janjuametal.com>
>> To: <info-m@nomuravtc.co.jp>
>> Sent: Thursday, November 22, 2012 3:22 AM
>> Subject: Nomura NN-160D....Parameters needed
>>
>>
>>> Dear Concerned,
>>>
>>> Good Day!!
>>>
>>> I recently bought two used Numura 160D machines from UK.
>>>
>>> Unfortunately, when I switched on the machines they don't have the
>>> parameters installed.
>>>
>>> I tried to get them from supplier but he refused to have any. I also
>>> tried my other contacts or sources but failed to get the right
>>> parameters.
>>>
>>> I also wrote to Gosiger.com and their respondent Mr Mark Walker said
>>> that they had forwarded my request to you i.e. Nomura VTC Japan but
>>> still got no reply.
>>>
>>> Now, It is only you who can help me. Therefore, I humbly request you
>>> to email me a copy of the subjected machine parameters files or the
>>> images of hard copy of the parameters.
>>>
>>> I would be utterly grateful to you.
>>>
>>> Regards,
>>> Jawad Haf
Posting Permissions
| | |
