| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| General CAM Discussion Discuss CAD/CAM software and Design software methods here! |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#1
08-19-2004, 07:57 PM
| ||||
| ||||
I am trying to find the link that was shown here a few weeks back that described the conversion of a Harley emblem in Corel to a CAM format for engraving, I have searched high and low and no luck. Anyone? Al
__________________ “Logic will get you from A to B. Imagination will take you everywhere.” Albert E. (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)    |
|
#2
08-19-2004, 10:07 PM
| ||||
| ||||
| http://www.torchmate.com/assistance/convert.htm About 10 threads down...Corel question or something like that. 
__________________ Gerry Mach3 2010 Screenset http://home.comcast.net/~cncwoodworker/2010.html (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
#3
08-20-2004, 08:26 AM
| ||||
| ||||
| Al_The_Man There are a couple of other approaches - but the Corel Trace function works good. Have you checked out the mini-product review listed as, The Quest for 2.5/3D, in the magazine. The Torchmate article/tutorial is part of what inspired me to do the review. Cheers - Jim
__________________ Experience is the BEST Teacher. Is that why it usually arrives in a shower of sparks, flash of light, loud bang, a cloud of smoke, AND -- a BILL to pay? You usually get it -- just after you need it. |
|
#4
08-20-2004, 12:47 PM
| ||||
| ||||
| Thanks to Both, Jim what is the magazine you are refering to? Al
__________________ “Logic will get you from A to B. Imagination will take you everywhere.” Albert E. (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
|
#5
08-20-2004, 01:18 PM
| ||||
| ||||
| Top of the page - here on the 'Zone - between Files List and Daily Posts Jim
__________________ Experience is the BEST Teacher. Is that why it usually arrives in a shower of sparks, flash of light, loud bang, a cloud of smoke, AND -- a BILL to pay? You usually get it -- just after you need it. |
| Sponsored Links |
| |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Student Versions of CAD and CAM Software | Jcadwell | General CAM Discussion | 8 | 08-04-2008 10:22 AM |
| CAD CAM Demo strategy questions? | Idle hands | General CAM Discussion | 6 | 05-24-2005 02:45 PM |
| Help/advice on CAM programs | itsme | General CNC (Mill and Lathe) Control Software (NC) | 7 | 01-14-2005 07:46 PM |
| Newbie CAM questions | WoodSnarfer | General CAM Discussion | 3 | 11-12-2004 08:15 AM |
| Cam design??? | anoel | G-Code Programing | 8 | 01-09-2004 09:06 AM |
| | |
Linear Mode
