I forgot to mention, on loading SYSTEM DISC 2.1 & 2.2 m/c starts ok,
We have Version 3.00JPY SOFTWARE for EX21
Atul M.
mescotc@sancharnet.in
We recently purchased a preowned 1996 Sodick A320D with EX21 Control, M/c with single floppy drive ( Epson 486 SE PC ) m/c in excellent condition with very low EDHours , M/c installed properly , test cuts taken OK.
Next week , while shuting down the m/c , operater made a mistake by switching "Source off" first , Next day on powering up the m/c , while booting m/c (SYSTEM LOADING stops at 11 ) displayed error " SYS2 Version up Install , insert floppy disk, press any key " , after that every time on booting, m/c displays same error and asks for system disc. I think this is abnormal.
Pls. suggest.
Atul M.
mescotc@sancharnet.in
+91 9823220324
Similar Threads:
I forgot to mention, on loading SYSTEM DISC 2.1 & 2.2 m/c starts ok,
We have Version 3.00JPY SOFTWARE for EX21
Atul M.
mescotc@sancharnet.in
Hey , No one yet on the forum aware about this problem ? Needs urgent help
your batteries om cpu-386 / cpu-86 are down. please change them. 980 Rs. /battery. ER-6 type.
Thanks for the reply, but my problem had been already sorted out.
Atul
On my A320d EX21 control, has a UPS fitted inside control cabinet , DENSEI make, But UPS doesn't functions. power to cotroller goes off , when power supply goes off.
pls.Suggest ,
Is it required to replace UPS , OR replace, batteries , is it required to buy UPS/batteries from Sodick ?
no need , buy from the market, 12V/5AH x 5 batteries.
total 5 batteries u need to replace.
REPLACED OLD BATTERIES WITH NEW ONES, 12V 4.5mA/h x 6 nos ,
1st day OK , run m/c for 6-8 hrs , but when i switch off the m/c the UPS was still working on battery mode & power to control was ON , So I switched off the UPS by opening RHS door.
2nd Day , after powering up the m/c , when I turned on ups, within few minutes UPS shows Overload, And gives ALARM , alarm doesn't go even when i switch off the Inverter switch , UPS is in Charging Mode , but alarm is ON
Pls. Suggest.
We have replaced batteries in the above UPS. Upon power up, we get an alarm light w/buzzer - charger light - and battery indicators are lit. We have no manuals on the UPS.
Does anyone know where to get an operators' manual?
Has anyone experienced this and what does it mean?
Regards.
How much machines do you have SODICK A320D
Hi Atul
I see that you had the same problem as I have now.
when you turn on the machine and start charging stops at 52 and SYS3 mistake, looking in the forums the solution appears, I saw the comment MR_SODICK that said that the batteries of CPU 386 and CPU 86 are down, effectively battery CPU 86 this down and draining fluid, replace the battery clean and reinstalling the CPU 86 turn on the machine and the same error.
cpu386 green LED on, yellow flashing off ,second yellow off.
cpu 86 green led ON (sometimes on but very slight) ,yellow off , secon yellow off
when turn on switch principal in machine then press source button , the UPS is off this OK ???
I could say as I fix this bug .please
thanks
please can you help me,
i have a problem on my sodick A320D ex21,
when it is loading it stops on (system loading 12/100) and show red message:
(SYS2 version up install
Insert the floppy disk in the USER side ,press the any kay.)
can you help me pls?
i need floppy disk 1 and 2 and 3
Hi guys, I have the same problem, in a MARK 25, the screen stops at SYSTEM LOADING 11, and then asks for "SYS2 VERSION UP INSTALL" and 3 install disks that i dont have, I already changed the two CR6 batteries included in the 386 CPU units, the UPS is ok.
Does anyone resolved this problem yet or has the installation disks that can share with us?
Good day, I have a similar problem, my epson 486se computer, I am loading the system, after this they turned off the machine and when restarting it indicates a message in Japanese that I insert the syatema diaco, then it tells me to follow the instructions of installation,?? what can i do, i need help
carlosek1@hotmail.com
Hi, good day, I have a problem in an ap500 cutting machine, when the pc was started the system was loaded in 12, the staff turned off the machine and then the pc asked to insert system disk, I put the disk but I do not know what to do , Can somebody help me.
hi
i have sodick A530D EX21 ,
when i turn the machine ,it give me error E229 .how can I fix it ?
thank you
Do you know how to install the software into Mark 25?
Good afternoon, i have this problem, and i dont find the solution, please help!
1) We turn on the Sodick A320, everything is normal, we move the X and Y axes, everything works perfectly.
2) We start the sparking program (go to CUTTING , C 777) and that is where the first error appears, as if the table were in contact with the wire. (photo Number 1). To clear up doubts, in case there was something touching the table and to make sure that there is no ST, we move the table in POSITION MOVE X=50. Next step, the table moves correctly, without detecting errors. But when we want to launch a program, it always puts the error in photo one.
3) We measure the voltage of the table with the nozzle, to confirm that the sources are not burned, and it shows 4.5vcc
4) Another error that usually appears is the one in photo number 2, it appears randomly, we move an axis and it appears. CPU STOP, or it also appears more often when we change the parameters in cutting, any condition that is set appears the error in photo no. 2 and if or if you have to restart the computer, it does not let you do anything.
Thank you very much for listening to us, and please, if you know how I can solve these errors, even if it means changing fonts or boards, let me know, so I can solve it as soon as possible. If you need a video, I'll gladly record it for you.
Here are the links of photo.
https://postimg.cc/gallery/tJ3zFWh
Thanks for your time
Hello, I have the same problem with my machine with the spu stop alert, friend, did you solve it?
I send you an affectionate greeting