I cut this out over the weekend. I cut it from 2 sided mirror.
Originally Posted by lakeside
Thanks for the Duesenberg Mike. I took a peek when no one was looking.
Toby D.
"Imagination and Memory are but one thing, but for divers considerations have divers names"
Schwarzwald
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
www.refractotech.com
I cut this out over the weekend. I cut it from 2 sided mirror.
That eagle looks sweet in mirror. Did you use any glue to hold the glass pieces together?
Brian
IS there a web sight or program that creates this type of Cutting File??
That eagle looks absolutly stunning in the mirror
WELL DONE
thats amazing, but how do you to cut mirror
You did a fantastic job on that Eagle. Are you going to sell these?
Toby D.
"Imagination and Memory are but one thing, but for divers considerations have divers names"
Schwarzwald
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
www.refractotech.com
Here's a link to the post with the EAGLE G-code file right here on "The Zone": http://www.cnczone.com/forums/showpo...82&postcount=8Originally Posted by Salty72
And here's the post with the DXF file: http://www.cnczone.com/forums/showpo...2&postcount=22
Enjoy!!!
HayTay
Don't be the one that stands in the way of your success!
Why thank you Hay Tay.
Have you found a new means of transportation yet? And did you ever find out what caused the Van to catch Fire?
Glad your still here
Toby D.
"Imagination and Memory are but one thing, but for divers considerations have divers names"
Schwarzwald
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
www.refractotech.com
Not a problem, and you are quite welcome. Glad to be of service.Originally Posted by tobyaxis
HayTay
Don't be the one that stands in the way of your success!
nice job on the Eagle is it acrylic.
Just a note to everyone.I've to upgrade my PC so I'm dumping programs on to disk. That's why all file were pulled.
Last edited by lakeside; 09-01-2006 at 03:25 AM.
The material that I used was Polycarbonate(lexan) 2 sided hardcoated mirror. It was scrap that I had left over from a previous cut job. I did end up glueing the feathers on. The bit that I cut this with was a few thousandths to big so the pieces didn't fit real tight. I also cut the Raptor the same day. It was 8' from head to tail. I sat it outside the shop the next day and a guy driveing by stopped and bought it before I could get pictures. His offer was just tooo good to pass up.
Thanks for all your responses.
here an update screen shot of my drawing I'm way pasted get carried away up to 48 meg now
Cool pics Mike can you send some to me?
Toby D.
"Imagination and Memory are but one thing, but for divers considerations have divers names"
Schwarzwald
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
www.refractotech.com
Does anyone have any files similar to these that haven't been posted here on "the Zone"?
http://www.hobbymasters.com/index.as...S&Category=215
I REALLY like the owl.
Yes, I believe there is a post someplace in here. I'll let you know where it is if I find it. They are both pics and DXF file so you can make your own.
Toby D.
"Imagination and Memory are but one thing, but for divers considerations have divers names"
Schwarzwald
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
www.refractotech.com
I have the eagle and t-rex and some of the others. It sure would be nice to have them all in one location.
I think that was the original intent of this post. To have one location where people could go to get actual files that are complete and "ready to cut".
Anyway, I'll keep searching for the others as well.
Thanks
Well I think the intent of this thread was to have a place where you could post your work.
Like the eagle that guy did it's a great job and I think it one of the best post in the thread (Seeing how I'm the one who started the thread, would you care to disagree...?) This thread is not just a place for you to get free files from. (BTW what have you shared with us?) I remove my files after 30 downloads
what are you looking for 3d files or just 2d vectored images?
Sorry, didn't realize that before. I agree, the mirrored eagle is my favorite also.
I haven't started my CNC machine yet. I plan on building Joe's machine.
I run wire EDM machines so any files I've created do not have a Z value. I'd be more than happy to share some of them. They're pretty rough though. Because of their small size, not much detail is needed.
I'll have to teach myself how to attach a file here. I've just been posting 'cause that's all I know how to do right now.
Your files are 2d DXF (data exchange file) That what all mine are. You set the Z depth when you program tool path. You can post a dxf (you may need to zip first) just post a note on what the file is. Then scroll down to the box that says Manage Attachment click on box and go to file
Coyote.DXF
Scorpion.DXF
See what I mean?