General Material Machining Solutions

Page 1 of 29 1234 11 ... LastLast
Threads 1 to 20 of 562

Forum: General Material Machining Solutions

Discuss Material Machining Problems and Solutions Here.

  1. Newbie- Need Recommendations to cut carbon fiber

    Started by FoxCNC1‎, 04-26-2017 03:44 PM
    • Replies: 9
    • Views: 174
    04-28-2017, 01:48 PM Go to last post
  2. Need Help!- CNC cutting alum. bracket (2d). - need some feeback please.

    Started by FoxCNC1‎, 03-26-2017 03:04 PM
    • Replies: 8
    • Views: 452
    04-26-2017, 03:41 PM Go to last post
  3. Need Help!- Phenolic Table Patch

    Started by 9r2a5m70‎, 04-03-2017 02:57 PM
    matrix, phenolic, pour, resin, section
    • Replies: 2
    • Views: 139
    04-21-2017, 09:39 AM Go to last post
  4. Newbie- Knots in my Aluminum?!?

    Started by jrmachinist‎, 12-23-2016 05:20 PM
    • Replies: 7
    • Views: 588
    04-20-2017, 11:49 PM Go to last post
  5. Milling Aluminium

    Started by Atomic_Sheep‎, 11-28-2016 08:21 AM
    • Replies: 10
    • Views: 669
    04-20-2017, 11:29 PM Go to last post
  6. Best material for a NEWBIE to practice on

    Started by Tomcat104‎, 04-09-2017 07:50 PM
    bits, cnc, material, order, suggestions
    • Replies: 9
    • Views: 227
    04-10-2017, 05:11 PM Go to last post
  7. Post Routing Printed ALU-Sheets problem

    Started by SignO24‎, 01-19-2017 04:14 PM
    aluminium, film, ink, laminating, problem
    • Replies: 1
    • Views: 343
    04-04-2017, 07:52 AM Go to last post
  8. Newbie- Bit Keeps Breaking - Need Help!

    Started by mannmade‎, 03-20-2017 02:38 PM
    artcam, bit, cnc, software
    • Replies: 6
    • Views: 239
    03-20-2017, 06:11 PM Go to last post
  9. Need Help!- jagged edges and flying sheets

    Started by Mahoney30‎, 02-22-2017 04:07 PM
    aluminum, axiz, cnc, fasten, feed
    • Replies: 1
    • Views: 263
    02-23-2017, 04:13 PM Go to last post
  10. Need Help!- Issues Cutting Copper

    Started by Teldin‎, 02-03-2017 09:25 PM
    blade, cnc, copper, cutting, pieces
    • Replies: 7
    • Views: 453
    02-04-2017, 10:15 PM Go to last post
  11. Help needed with material selection

    Started by Kickin Wing‎, 01-30-2017 04:22 PM
    crazy, cut, finally, rolled, warp
    • Replies: 1
    • Views: 183
    01-30-2017, 04:51 PM Go to last post
  12. Ideal paint for machining?

    Started by ryanjg117‎, 01-19-2017 01:44 AM
    • Replies: 0
    • Views: 203
    01-19-2017, 01:44 AM Go to last post
  13. Build Thread- No Fog Mist Coolant

    Started by Jim Dawson‎, 01-16-2017 07:07 PM
    • Replies: 8
    • Views: 483
    01-17-2017, 11:22 AM Go to last post
  14. did anyone used " punch " tapping ?

    Started by deadlykitten‎, 01-17-2017 01:34 AM
    kindly, punch, tapping
    • Replies: 0
    • Views: 173
    01-17-2017, 01:34 AM Go to last post
  15. End mills bigger than shank for deep pockets?

    Started by Jim27‎, 12-31-2016 10:34 AM
    cutting, end, length, mills, shank
    • Replies: 10
    • Views: 645
    01-01-2017, 04:32 PM Go to last post
    • Replies: 3
    • Views: 234
    12-30-2016, 04:22 PM Go to last post
    • Replies: 1
    • Views: 284
    12-12-2016, 04:08 AM Go to last post
  16. Micro-holes machining - economical options

    Started by hubihubi2‎, 11-27-2016 06:27 PM
    approx, holes, machining, options, steel
    • Replies: 0
    • Views: 232
    11-27-2016, 06:27 PM Go to last post
  17. Need Help!- rPM calculation

    Started by sered‎, 11-16-2016 04:13 AM
    calculation, cnc, fluts, mill, rpm
    • Replies: 0
    • Views: 309
    11-16-2016, 04:13 AM Go to last post
  18. Need Help!- Milling D2 Tool Steel

    Started by trikerider2oo7‎, 03-24-2010 09:20 PM
    000rpm, already, far, isnt, machinis
    • Replies: 6
    • Views: 10,870
    11-14-2016, 06:34 PM Go to last post

Page 1 of 29 1234 11 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 6 users browsing this forum. (0 members & 6 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands