General Material Machining Solutions

Page 1 of 29 1234 11 ... LastLast
Threads 1 to 20 of 564

Forum: General Material Machining Solutions

Discuss Material Machining Problems and Solutions Here.

  1. What grade of steel for rack and pinion?

    Started by Eddieb378‎, Yesterday 04:50 PM
    • Replies: 0
    • Views: 46
    Yesterday, 04:50 PM Go to last post
  2. Newbie- Need Recommendations to cut carbon fiber

    Started by FoxCNC1‎, 04-26-2017 03:44 PM
    • Replies: 10
    • Views: 300
    05-24-2017, 06:12 PM Go to last post
  3. Need Help!- CNC cutting alum. bracket (2d). - need some feeback please.

    Started by FoxCNC1‎, 03-26-2017 03:04 PM
    • Replies: 9
    • Views: 530
    05-24-2017, 06:05 PM Go to last post
  4. Need Help!- Issues Cutting Copper

    Started by Teldin‎, 02-03-2017 09:25 PM
    blade, cnc, copper, cutting, pieces
    • Replies: 9
    • Views: 582
    05-14-2017, 12:31 PM Go to last post
  5. Titanium swarf problem - re-posted in correct forum

    Started by Zorbit‎, 05-14-2017 08:50 AM
    coolant, forum, high, job, swarf
    • Replies: 0
    • Views: 138
    05-14-2017, 08:50 AM Go to last post
  6. Need Help!- Phenolic Table Patch

    Started by 9r2a5m70‎, 04-03-2017 02:57 PM
    matrix, phenolic, pour, resin, section
    • Replies: 2
    • Views: 160
    04-21-2017, 09:39 AM Go to last post
  7. Newbie- Knots in my Aluminum?!?

    Started by jrmachinist‎, 12-23-2016 05:20 PM
    • Replies: 7
    • Views: 623
    04-20-2017, 11:49 PM Go to last post
  8. Milling Aluminium

    Started by Atomic_Sheep‎, 11-28-2016 08:21 AM
    • Replies: 10
    • Views: 716
    04-20-2017, 11:29 PM Go to last post
  9. Best material for a NEWBIE to practice on

    Started by Tomcat104‎, 04-09-2017 07:50 PM
    bits, cnc, material, order, suggestions
    • Replies: 9
    • Views: 257
    04-10-2017, 05:11 PM Go to last post
  10. Post Routing Printed ALU-Sheets problem

    Started by SignO24‎, 01-19-2017 04:14 PM
    aluminium, film, ink, laminating, problem
    • Replies: 1
    • Views: 354
    04-04-2017, 07:52 AM Go to last post
  11. Newbie- Bit Keeps Breaking - Need Help!

    Started by mannmade‎, 03-20-2017 02:38 PM
    artcam, bit, cnc, software
    • Replies: 6
    • Views: 259
    03-20-2017, 06:11 PM Go to last post
  12. Need Help!- jagged edges and flying sheets

    Started by Mahoney30‎, 02-22-2017 04:07 PM
    aluminum, axiz, cnc, fasten, feed
    • Replies: 1
    • Views: 276
    02-23-2017, 04:13 PM Go to last post
  13. Help needed with material selection

    Started by Kickin Wing‎, 01-30-2017 04:22 PM
    crazy, cut, finally, rolled, warp
    • Replies: 1
    • Views: 197
    01-30-2017, 04:51 PM Go to last post
  14. Ideal paint for machining?

    Started by ryanjg117‎, 01-19-2017 01:44 AM
    • Replies: 0
    • Views: 213
    01-19-2017, 01:44 AM Go to last post
  15. Build Thread- No Fog Mist Coolant

    Started by Jim Dawson‎, 01-16-2017 07:07 PM
    • Replies: 8
    • Views: 515
    01-17-2017, 11:22 AM Go to last post
  16. did anyone used " punch " tapping ?

    Started by deadlykitten‎, 01-17-2017 01:34 AM
    kindly, punch, tapping
    • Replies: 0
    • Views: 191
    01-17-2017, 01:34 AM Go to last post
  17. End mills bigger than shank for deep pockets?

    Started by Jim27‎, 12-31-2016 10:34 AM
    cutting, end, length, mills, shank
    • Replies: 10
    • Views: 683
    01-01-2017, 04:32 PM Go to last post
    • Replies: 3
    • Views: 245
    12-30-2016, 04:22 PM Go to last post
    • Replies: 1
    • Views: 303
    12-12-2016, 04:08 AM Go to last post
  18. Micro-holes machining - economical options

    Started by hubihubi2‎, 11-27-2016 06:27 PM
    approx, holes, machining, options, steel
    • Replies: 0
    • Views: 246
    11-27-2016, 06:27 PM Go to last post

Page 1 of 29 1234 11 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 16 users browsing this forum. (0 members & 16 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands