Spot Size measuring?


Results 1 to 13 of 13

Thread: Spot Size measuring?

  1. #1


  2. #2
    Registered
    Join Date
    Dec 2008
    Location
    USA
    Posts
    1258
    Downloads
    0
    Uploads
    0

    Default

    Burn a hole in a piece of paper, use just enough power to produce a clean hole and ensure the beam is focused.

    The next challenge is to measure the hole, a microscope with reticle would be ideal.

    You can get pretty accurate results.

    Zax.



  3. #3
    Registered Litografa's Avatar
    Join Date
    Jul 2008
    Location
    Lithuania
    Posts
    776
    Downloads
    0
    Uploads
    0

    Default

    We measure spot size on Alumamark. With use of paper mark is slightly bigger than real spot size due paper burning. With Alumamark you have practically exact size of dot. Of course perfect focusing is necessary.



  4. #4
    Registered
    Join Date
    Dec 2008
    Location
    USA
    Posts
    1258
    Downloads
    0
    Uploads
    0

    Default

    Actually the paper method with very low power produces accurate results when compared to electronic based measurement system. It even shows the halo or HAZ (heat affected zone) around the focused beam.

    You will of course need a sufficiently high mag scope with measurement capability to determine the actual spot size vs. the halo area.

    I have not tried Alumamark but that should work the same way, just with more power required.

    Zax.



  5. #5
    Registered Litografa's Avatar
    Join Date
    Jul 2008
    Location
    Lithuania
    Posts
    776
    Downloads
    0
    Uploads
    0

    Default

    And what do you think about glass or stone? Looks like on glass will be best results for accuracy of spot measurement?



  6. #6
    Member
    Join Date
    Jan 2006
    Location
    Belgium
    Posts
    114
    Downloads
    0
    Uploads
    0

    Smile

    Heloo Litografa & Zax,

    to measure the spot size, must i give only a short schot, or must i engraving a line?

    Pierke



  7. #7
    Registered Litografa's Avatar
    Join Date
    Jul 2008
    Location
    Lithuania
    Posts
    776
    Downloads
    0
    Uploads
    0

    Default

    I am using single shot.



  8. #8
    Registered
    Join Date
    Dec 2008
    Location
    USA
    Posts
    1258
    Downloads
    0
    Uploads
    0

    Default

    Exactly - single shot.

    It can be done by manually firing the laser at low power, just make the pulse as short as possible or if your system can send a single pulse from the software that is better.

    Zax.



  9. #9
    Registered kewlkiwi's Avatar
    Join Date
    Oct 2004
    Location
    New Zealand
    Posts
    158
    Downloads
    0
    Uploads
    0

    Default

    Cut a slot, and use feeler gauge set?

    Bob



  10. #10
    Registered
    Join Date
    Dec 2008
    Location
    USA
    Posts
    1258
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by kewlkiwi View Post
    Cut a slot, and use feeler gauge set?
    Bob,

    That would work. I was trying to think of a simple way for someone to measure it without a scope or other equipment.

    I have access to so much technology I couldn't see the 'simple' method.

    Thanks,
    Zax.



  11. #11
    Member
    Join Date
    Jan 2006
    Location
    Belgium
    Posts
    114
    Downloads
    0
    Uploads
    0

    Smile

    Thanks to all for the verry good info.
    I'm glad that i can try it on several ways.

    Pierke



  12. #12
    Registered MonoNeuron's Avatar
    Join Date
    Aug 2003
    Location
    Australia
    Posts
    494
    Downloads
    0
    Uploads
    0

    Default

    I just use a very powerful magnifying glass and measure the spot size with a dial caliper. It's accurate to about 0.0005".
    I place a piece of thin cardboard bent over at 1 end to form a ramp about 10mm high and 50mm long then burn a spot every 5mm up the ramp. Then all I do is find out which spot is the smallest and measure that against the height from the lens to also get the focal distance for setting up the laser head.
    regards
    Richard.

    I am not completely useless.......I can always serve as a BAD example.


  13. #13
    Member
    Join Date
    Jan 2006
    Location
    Belgium
    Posts
    114
    Downloads
    0
    Uploads
    0

    Smile

    Hello Richard,

    this is an verry easy way to find out to spot size (measuring)
    I'll try this.
    Thank you!

    Pierke



Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Spot Size measuring?

Spot Size measuring?