Rabbit Laser not working


Results 1 to 18 of 18

Thread: Rabbit Laser not working

  1. #1
    Registered
    Join Date
    Sep 2007
    Location
    USA
    Posts
    16
    Downloads
    0
    Uploads
    0

    Exclamation Rabbit Laser not working

    Hello everyone. Found the forum. Great site. I recently purchased a Rabbit HX6090SC. got it home worked great. The second time I used it the power supply blew. Fan inside was un pluged and over heated. Received a new power supply but not the same. Same wattage but for one of their other machines. They said it would work. Have it installed the way they want it but the laser fires just won't leave the tube ! The laser seems to arc at the metal ring whrer you make the connection for the ground on the laser tube. Any Ideas ? Any one ever hear of this ? I replaced the laser tube with a spare I bought, same thing. Any help would really be great. Thanks, Jim

    Similar Threads:


  2. #2
    Registered
    Join Date
    Aug 2007
    Location
    USA
    Posts
    61
    Downloads
    0
    Uploads
    0

    Default

    Wish I could help. Maybe next week once mine goes down. These machines have to be tested before they leave the port!

    Last edited by ArturoV; 10-04-2007 at 12:19 AM.


  3. #3
    Registered
    Join Date
    Jul 2007
    Location
    US
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default

    Help please.

    My new CO2 laser machine has a a working area of 1000mm X 600mm. The software came with the machine is the DSP5.0. The machine only gives about 50% working area around the center of the machine table.

    Here is what I want to cut:
    [IMG]E:\WorkingTable.JPG[/IMG]

    Then I got this message:
    [IMG]E:\Exceeds working table.JPG[/IMG]

    Here is the machine setting at the default setup of the software:
    [IMG]E:\Laser_Machine-Option_Worktable.JPG[/IMG]

    Thanks.

    I guess I have problem to attach pic here.

    Attached Thumbnails Attached Thumbnails Rabbit Laser not working-workingtable-jpg   Rabbit Laser not working-exceeds-working-table-jpg   Rabbit Laser not working-laser_machine-option_worktable-jpg  
    Last edited by Laser123; 10-06-2007 at 12:48 AM. Reason: pic not shown


  4. #4
    Registered
    Join Date
    Apr 2007
    Location
    Colombia
    Posts
    641
    Downloads
    0
    Uploads
    0

    Default

    In the software screen Go to file/options/worktable there you can set the size of your table. After that go to printing icon in the software screen and download the config. import the PLT or AI file and download it to the machine.
    Use corel 11 to draw export as .PLT . Import to the machine software

    Here in the forum to download pictures: go advanced



  5. #5
    Registered
    Join Date
    Jul 2007
    Location
    US
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default

    [QUOTE=Laser123;350253]Help please.

    My new CO2 laser machine has a a working area of 1000mm X 600mm. The software came with the machine is the DSP5.0. The machine only gives about 50% working area around the center of the machine table.

    Here is what I want to cut:
    [IMG]E:\WorkingTable.JPG[/IMG]



    Then I got this message:
    [IMG]E:\Exceeds working table.JPG[/IMG]

    Here is the machine setting at the default setup of the software:
    [IMG]E:\Laser_Machine-Option_Worktable.JPG[/IMG]

    Thanks.

    I guess I got the attachments here now.

    Attached Thumbnails Attached Thumbnails Rabbit Laser not working-workingtable-jpg   Rabbit Laser not working-exceeds-working-table-jpg   Rabbit Laser not working-laser_machine-option_worktable-jpg  


  6. #6
    Registered
    Join Date
    Sep 2007
    Location
    EGYPT
    Posts
    11
    Downloads
    0
    Uploads
    0

    Default

    [QUOTE=Laser123;350970]
    Quote Originally Posted by Laser123 View Post
    Help please.

    My new CO2 laser machine has a a working area of 1000mm X 600mm. The software came with the machine is the DSP5.0. The machine only gives about 50% working area around the center of the machine table.

    Here is what I want to cut:
    [IMG]E:\WorkingTable.JPG[/IMG]

    Then I got this message:
    [IMG]E:\Exceeds working table.JPG[/IMG]

    Here is the machine setting at the default setup of the software:
    [IMG]E:\Laser_Machine-Option_Worktable.JPG[/IMG]

    Thanks.

    I guess I got the attachments here now.

    Please follow these steps:
    1- delete all the letters in you drawing except one, ( for example the inner circle of th O letter.
    2- click on the 10th button from the left in the button bar, ( zoom to the object).

    3-if you cannot see the shape that you left in step 1 filling all the screen that means there are more line outside the working area, check you design.

    I hope that helps



  7. #7
    Registered
    Join Date
    Apr 2007
    Location
    Colombia
    Posts
    641
    Downloads
    0
    Uploads
    0

    Default

    When you receive your machine did it come with the size of the table or it was 900 x600 the input? If so, Did you download the config in the laser output? Because you can have that config in your PC as you say onlu have about 50% of centered working area... please check it



  8. #8
    Registered
    Join Date
    Apr 2007
    Location
    Colombia
    Posts
    641
    Downloads
    0
    Uploads
    0

    Default

    Jim Dornon, That arc coming out from the tube, check if the welding has picks , if it is not plain, that can make thi current to jump like that.
    Other thing is that the tube could have broken the internal conections for the catode and anode.. BE CAREFULL WITH THAT WIRES 20.000 volts there!!!



  9. #9
    Registered
    Join Date
    Sep 2007
    Location
    USA
    Posts
    16
    Downloads
    0
    Uploads
    0

    Default Laser

    Welding pics. Do you mean were I soldered the connection to the laser tube ? Jim

    Rabbit Laser HX6090SC


  10. #10
    Registered
    Join Date
    Apr 2007
    Location
    Colombia
    Posts
    641
    Downloads
    0
    Uploads
    0

    Default

    yes in the anode and catode wires, the weld should be clean , no high points (picks) wire left as a needle, the arc jumps from there



  11. #11
    Member
    Join Date
    Aug 2004
    Location
    US
    Posts
    2849
    Downloads
    0
    Uploads
    0

    Default

    So, where the Rabbit Lazer Guy.....he always was running around he saying how he could help...Quality Number One....etc. and his little partner aka nemesis....



  12. #12
    Registered
    Join Date
    Aug 2005
    Location
    Israel
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default

    hello guys as a distributing of laser machines in israel i will be happy to give u solution

    did u download the new machine cfg file?
    downloading the cfg file with correct setting should solve the problem.
    CAT



  13. #13
    Registered
    Join Date
    Sep 2007
    Location
    USA
    Posts
    16
    Downloads
    0
    Uploads
    0

    Question I don't understand

    Not sure I follow. Can you explain ? Jim

    Rabbit Laser HX6090SC


  14. #14
    Registered
    Join Date
    Aug 2005
    Location
    Israel
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default ....

    ctrl+y will center all the job then use the "zoom to all object "on top-if there is some job out of the working area it will show it.


    if its a dsp offline machine u should download first the machine parameters as a cfg file-all details inside like the working table size......


    DID ANY ONE NOTICE A BUG IN THE 5.0 VERSION?
    only dspoffline version?once u want to download the file ,on the prossesing part the software jumps out-i am still waiting for solution from the software company.


    did anyone else got the same problem?



  15. #15
    Registered
    Join Date
    Apr 2007
    Location
    Colombia
    Posts
    641
    Downloads
    0
    Uploads
    0

    Default

    Yes I have seen it , we reinstalled sofware and it dissapear but not at all. sometimes it jumps again



  16. #16
    Registered
    Join Date
    Aug 2005
    Location
    Israel
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default hello lamicron

    do u have the dsp5.0 and u use dspoffine machine?

    can u please back up the "language.ini"file and delete

    then let me know if this problem apear again?
    is it jumping out only on the calculating data part?

    we think this problem apear only if your windows is not english version .But we are not sure yet.

    thanks

    CAT



  17. #17
    Registered
    Join Date
    Apr 2007
    Location
    Colombia
    Posts
    641
    Downloads
    0
    Uploads
    0

    Default

    Yes , now we know the spanish XP version doesnt work well, it took a long time to know it.
    I don't understand the other questions
    do u have the dsp5.0 and u use dspoffine machine?

    can u please back up the "language.ini"file and delete

    then let me know if this problem apear again?
    is it jumping out only on the calculating data part?



  18. #18
    Registered
    Join Date
    Aug 2005
    Location
    Israel
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default hi again

    do your machine is USB ?



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Rabbit Laser not working

Rabbit Laser not working