laser sofware
we are looking for a relative low cost software. that is great for just plan 2d work we are going to be cutting parts and strips for developing prog dies. if you have any suggestiong it would greatly appreciated..
thank you,
brian
Similar Threads:
- Newbie- DNC Sofware Sugestions
- Problem- Need new Sofware?
- sofware confusion
Software / Service
You could take a look at SmartCam that will do what you want and maybe a little more for about 4k http://www.SmartCAMcnc.com/ . There are some other programs that may be cheaper but someone else will have to speak for them. I also have a service that I could write programs for your laser if you have an interest in that. Take a look at my home page for more information.
Independent CNC Programmer
www.ctcn,net/~3kings/
software
we are looking for some about 1k or less we don't need any thing fancy just plain jane will work
Perhaps DSP software is a good choice
I hoped demonstrates my cnc,laser and model
www.modelcn.cn
on that sofware is dsp the manufacture of it or is that the name of it
name
I hoped demonstrates my cnc,laser and model
www.modelcn.cn
ty
bye any chance do you know who makes it?
thank you i'm glad for the help
It is certainly me! !!
I hoped demonstrates my cnc,laser and model
www.modelcn.cn
3 sets of my already successful manufacture ,laser cut machine uses the sotware
it is good.
I hoped demonstrates my cnc,laser and model
www.modelcn.cn
so you wrote the software?
No, I bought the controller, and that software. He can use coreldraw12 and autocad2006 while controlling laser energy while using color and pwm while using win-xp.
I hoped demonstrates my cnc,laser and model
www.modelcn.cn
brain cizauskas,
There is an offer software which i found it is quite good, and if you know autocad it is even better due to the low cost of 295 euro.
This offer is valid for another few days.
The link for the features is as below.
http://www.givemepower.de/PowerCAD_features.html
From there you can go to the online shop.
we have autocad we are looking for 2d cam software
Sorry to have misunderstood your software needs.
You had not stated your type of controller for which the software to be use.
its a 1994 mazak with a mazak l-32 control...sorry it was my fault for not stateing it earier
If i am not mistaken,the laser resonator is made by panasonic.
I think it is very difficult to get a cheap software for your machine but at least some member can now help you out with your above info.
look at the mpc03-lv made in china by step-servo and costs $1000 USD web site is www.step-servo.com which is developed from DSP & FPGA tecnology
It would appear that they make most of the drivers for all China laser machines although you will have to buy a 64 pin cable for around $20 USD which then conects to a breakout board which is to me basicly a termenal block, not sure of the cost of this but should not be much, if you buy this from anyone other than the manufacter you will not only pay their marked up prices but may find also that they vanish of the face of the earth so buy direct
hope this is of use to you
Try solustan.com very good software with good backup.
DSP 4.0 operating help requested
Hope someone here can help. We are using Corel X3 and our laser utilzes the software DSP 4.0. We are just learning to use our new laser. Our immediate problem arises when importing or opening a file generated in Corel (also Autocad), into the DSP 4.0 program. The artwork seems to open anywhere on the worktable, never in the lower left corner or upper left corner as it was saved in Corel.
What do we need to do or change so it will open in DSP 4.0 as it was saved or into a corner?
Albert
for profiling software, I'd look at OneCNC...
Posting Permissions
Reply with Quote